Polaris Sportsman 570 EFI Owner'S Manual Download

Page: 44 / 148

FEATURES AND CONTROLS

Instrument Cluster

Diagnostic Display Code Definitions

Open Load:

There is a break in the wires that lead to the item listed in

the chart (injector, fuel pump, etc.), or the item has failed.

Short-to-Ground:

The wire is shorted to ground between the electronic

control unit and the item listed in the chart.

Shorted Load

: The wires leading to the item listed in the chart are

shorted together, or the item has shorted internally.

Short-to-Battery:

The wire leading from the item listed in the chart to

the electronic control unit is shorted to a wire at battery voltage.

SPORTSMAN 570 EFI/570 EPS Diagnostic Codes

Component

Condition

SPN

FMI

Throttle Position Sensor

Voltage Too High

Voltage Too Low

Engine Temperature Sensor

Voltage Too High

110

Voltage Too Low

110

Temperature Too High

110

Engine Overheat Shutdown

110

Intake Air Temperature Sensor

Voltage Too High

105

Voltage Too Low

105

Manifold Absolute Pressure Sensor

Voltage Too High

102

Voltage Too Low

102

Crankshaft Position Sensor

Circuit Fault

636

Gear Sensor Signal

Voltage Too Low (to Calibrate)

523

Voltage Too High

523

Signal Fault

523

Injector 1 (MAG)

Driver Circuit Open/Grounded

651

Driver Circuit Short to B+

651

Ignition Coil Primary Driver 1 (MAG)

Driver Open/Grounded

1268

Driver Circuit Short to B+

1268

Fuel Pump Driver Circuit

Driver Circuit Open/Grounded

1347

Driver Circuit Short to B+

1347

Fan Relay Driver Circuit

Driver Circuit Open/Grounded

1071

Driver Circuit Short to B+

1071

Summary of Contents for Sportsman 570 EFI





















































































































































Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands

Polaris Sportsman 570 EFI, Owner'S Manual

Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands