Polaris Sportsman 570 EFI Owner'S Manual Download | Manualshive

Page: 7 / 148

background image

5

INTRODUCTION

Failure to heed the warnings and safety precautions contained in this manual
can result in severe injury or death. A POLARIS ATV is not a toy and can be
hazardous to operate. This vehicle handles differently than other vehicles, such
as motorcycles and cars. A collision or rollover can occur quickly, even during
routine maneuvers like turning, or driving on hills or over obstacles, if you fail to
take proper precautions.
• Read this owner’s manual. Understand all safety warnings, precautions and

operating procedures before operating a POLARIS ATV. Keep this manual
with the ATV.

• Never operate an ATV without proper instruction. Take a certified ATV safety

training course (www.atvsafety.org).

• This vehicle is an ADULT VEHICLE ONLY. Operation is prohibited for anyone

under 16 years of age.

• Never permit a guest to operate the ATV unless the guest has read this

manual and all product labels and has completed a certified safety training
course (www.atvsafety.org).

European Vibration and Noise

The driver-perceived noise and hand/arm and whole body vibration
levels of this machinery is measured per prEN 15997.

The operating conditions of the machinery during testing:

The vehicles were in like-new condition. The environment was
controlled as indicated by the test procedure(s).

The uncertainty of vibration exposure measurement is dependent on
many factors, including:
• Instrument and calibration uncertainty
• Variations in the machine such as wear of components
• Variation of machine operators such as experience or physique
• Ability of the worker to reproduce typical work during measurements
• Environmental factors such as ambient noise or temperature

WARNING

«
...
5
6
7
8
9
...
»

Summary of Contents for Sportsman 570 EFI





















































































































































Reviews:

No comments

Related manuals for Sportsman 570 EFI

Brand: Yutrax Pages: 10

Brand: Yepp Pages: 10

Brand: Massimo Motor Pages: 165

Brand: Hisun Pages: 93

Brand: Clam Corp Pages: 4

Brand: Clam Corp Pages: 6

Falcon Go-kart 2018

Brand: J&J Amusements Pages: 58

Brand: Strongway Pages: 3

Brand: HOMCOM Pages: 35

Brand: PRONAR Pages: 135

Sportsman 90 2011

Brand: Polaris Pages: 12

Brand: Let's Go Aero Pages: 3

jay 2016 series

Brand: Jayco Pages: 157

Brand: Range Road Pages: 21

Brand: Taylor-Dunn Pages: 233

YXZ 1000R SS 2022

Brand: Yamaha Pages: 216

Indy 340 Deluxe 2000

Brand: Polaris Pages: 52

2012 RANGER RZR 570

Brand: Polaris Pages: 403

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands