Polaris Sportsman 570 EFI Owner'S Manual Download

Page: 98 / 148

MAINTENANCE

Tires

Wheel Installation

1. Place the transmission in PARK.

2. Lock the parking brake.

3. Place the wheel on the hub with the valve stem toward the outside

and rotation arrows on the tire pointing toward forward rotation.

4. Install the wheel nuts and finger-tighten them.

5. Lower the vehicle to the ground.

6. Torque the wheel nuts to specification.

WARNING!

Loose nuts could cause a tire to come off during operation, which

could result in an accident or rollover. Always ensure that all nuts are torqued to
specification.

Wheel Nut Torque Specifications

Check the wheel nut torques occasionally and when they've been
loosened for maintenance service.

Nut Type

Nut Torque

Lug Nut (Aluminum

Wheels)

30 ft. lbs. (41 Nm)

PLUS 1/4 TURN

2-Piece Flange Nut

(Steel Wheels)

27 ft. lbs. (37 Nm)

Summary of Contents for Sportsman 570 EFI





















































































































































Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands

Polaris Sportsman 570 EFI, Owner'S Manual

Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands