background image

- 39 -

1200_GB-ANHANGA_SICHERHEIT

SUPPLEMENT - A

GB

20%

Kg

9.) Transport of persons prohibited

a.  The transport of persons on the machine is not  permitted. 
b.  The machine may only be driven on public roads when 

in the position sti pu la ted for road trans port. 

10.) Driving ability with auxiliary  equipment 

a.  The towing vehicle is to be sufficiently equiped with 

weights at the front or 
at the rear in order to 
gua ran tee the steering 
and braking capacity (a 
mi ni mum of 20% of the 
 vehicle’s tare weight on 
the front axle).

b.  The driving  ability is 

in fluen ced by ground 
con di tions and by the 
 auxiliary equip ment. The dri ving must be adap ted to the 
cor re spon ding  terrain and ground  conditions. 

c.    When driving through curves with a con nec ted  appliance, 

ob ser ve the ra dius and  swinging mass of the appliance. 

d.    When travelling in a curve with attached or semimounted 

implements, take into account the working range and 
swing mass of the implement!

11.) General 

a.  Before attaching implement to three-point linkage, move 

system lever into a position whereby unintentional raising 
or lowering is ruled out!

b.  Danger of injury exists when coupling implement to 

trac tor!

c.  Danger of injury through crushing and cutting exists in 

the three-point linkage area!

d. Do not stand between tractor and implement when 

using three-point linkage external operation!

e.  Attach and detach drive shaft only when motor has 

stop ped.

f.  When transporting with raised implement, secure 

ope ra ting lever against lowering! 

g.  Before leaving tractor, lower attached implement to the 

ground and remove ignition key!

h. Nobody is to stand between tractor and implement 

without tractor being secured against rolling using 
parking brake and/or wheel chocks!

i.   For all maintenance, service and modification work, 

turn driving motor off and remove universal drive.

12.) Cleaning the machine

a.  Do not use high-pressure washers for the cleaning of 

bearing- and hydraulic parts.

Summary of Contents for NOVACAT 225 H























































Reviews: