Poettinger NOVACAT 225 H Operator'S Manual Download

Page: 7 / 54

(348) ANBAU 0000-GB

ATTACHING TO TRACTOR

- 7 -

Adjusting lower links

• The drive shaft (GW) position should be approximately horizontal

when mowing.

- Set the tractor's lifting gear accordingly (H1)

- Set the tractor hydraulics (ST) using the bit stop.

This height allows optimal evenness when working on uneven ground
and need not be changed for swinging cutter bar up.

- Connect hydraulic snap coupling for swivel cylinder.

Important recommendation!

A transfer, which is located near the gear, advises which p.t.o. speed

your mower unit is equipped for.

Standard:

Gear for power take-off

1000 rpm.

Optional exra:

Gear for power take-off

500 rpm.

Order number: spare part book

Fitting drive shaft

- Before operating for the first time, drive shaft is to be checked and

adapted if necessary. See alse chapter "Drive Shaft" in supplement
B.

Parking in the open

When parking for longer periods in the open, clean plunger rods and
then coat with grease.

TD 4-00-1

1000 rpm

540 rpm

TD 18/96/2

FETT

TD 49/93/2

Summary of Contents for NOVACAT 225 H























































Search results

Summary of Contents for NOVACAT 225 H

Reviews:

Related manuals for NOVACAT 225 H

Brands by name

Popular brands

Poettinger NOVACAT 225 H, Operator'S Manual

Search results

Summary of Contents for NOVACAT 225 H

Reviews:

Related manuals for NOVACAT 225 H

Brands by name

Popular brands