Poettinger NOVACAT 225 H Operator'S Manual Download

Page: 52 / 54

Name and address of the manufacturer:

Pöttinger Landtechnik GmbH
Industriegelände 1
AT - 4710 Grieskirchen

Machine (interchangeable equipment)

mower
Type
Serial no.

The manufacturer declares that the machines adhere to all relevant provisions in the
following EU directive:

machinery 2006/42/EG

In addition to this, the manufacturer also declares adherence to the other following EU
directives and/or relevant provisions

Source of applied, harmonised norms:

EN ISO 12100

EN ISO 4254-1

EN ISO 4254-12

Source of applied miscellaneous technical norms and / or specifications:

Person responsible for documentation:

Andreas Gadermayr
Industriegelände 1
A-4710 Grieskirchen

EC Conformity Declaration

Original Conformity Declaration

Klaus Pöttinger,
Corporate management

Grieskirchen, 22.02.2016

7KH&(QRUPLVQRWYDOLGLQWKH8QLWHG6WDWHVRI$PHULFDDQG&DQDGD

NOVACAT

225 / 225 ED

265 / 265 ED

377 378

Summary of Contents for NOVACAT 225 H























































Search results

Summary of Contents for NOVACAT 225 H

Reviews:

Related manuals for NOVACAT 225 H

Brands by name

Popular brands

Poettinger NOVACAT 225 H, Operator'S Manual

Search results

Summary of Contents for NOVACAT 225 H

Reviews:

Related manuals for NOVACAT 225 H

Brands by name

Popular brands