Phytec phyCARD-M Hardware Manual Download Page 47 | Manualshive

Page: 47 / 128

background image

System

Memory

©

PHYTEC Messtechnik GmbH 2010 L-750e_1

39

7.2

NAND Flash Memory (U13)

Use of Flash as non-volatile memory on the phyCARD-M provides an
easily reprogrammable means of code storage. The following Flash
devices can be used on the phyCARD-M:

Manufacturer

NAND Flash P/N

Density
(MByte)

Samsung K9F1G08UOC 128

Table 10:

Compatible NAND Flash devices

Additionally, any parts that are footprint (48-TSOP) and functionally
compatible with the NAND Flash devices listed above may also be
used with the phyCARD-M.

These Flash devices are programmable with 3.3 V. No dedicated
programming voltage is required.

As of the printing of this manual these NAND Flash devices generally
have a life expectancy of at least 100,000 erase/program cycles and a
data retention rate of 10 years.

The NAND Flash memory is connected to the NAND Flash Controller
(NFC).

7.3

I²C EEPROM (U6)

The phyCARD-M is populated with an ST 24W32C

1

non-volatile

4KByte EEPROM with an I²C interface at U6. This memory can be
used to store configuration data or other general purpose data. This
device is accessed through I²C port 1 on the i.MX35. The control
registers for I²C port 1 are mapped between addresses 0x43F8 0000
and 0x43F8 3FFF. Please see the

i.MX35 Reference

Manual for

detailed information on the registers.

1

:

See the manufacturer’s data sheet for interfacing and operation.

«
...
45
46
47
48
49
...
»

Summary of Contents for phyCARD-M

































































































































Reviews:

No comments

Related manuals for phyCARD-M

Brand: Aaeon Pages: 100

Brand: Aaeon Pages: 120

Brand: Aaeon Pages: 116

Brand: Aaeon Pages: 119

Brand: Aaeon Pages: 111

Brand: Aaeon Pages: 106

Brand: Aaeon Pages: 48

Brand: Aaeon Pages: 44

Brand: Abit Pages: 72

Brand: TYAN Pages: 67

Brand: IEI Technology Pages: 15

Brand: JETWAY Pages: 49

Brand: Zotac Pages: 56

Brand: Texas Instruments Pages: 9

Brand: ASROCK Pages: 226

IMBA-BDE-1518-R10

Brand: IEI Technology Pages: 14

Brand: National Semiconductor Pages: 22

PRESTIGE X570 CREATION

Brand: MSI Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands