manualshive.com logo in svg

Philips System4 LTC 2650/00, User Manual

Share
Download
Philips System4 LTC 2650/00 User Manual Download Page 72

72

6

System4

ACTIVE ZONE APPLICATION

6.1

Description

The 

Active Zone Application

is used by the installer or the

administrator to configure the areas of a camera view where any
activity causes an 

Action 

event to occur. The application is

invoked by positioning the mouse cursor on the 

Camera

icon in

the Map Container and clicking on the right mouse button, or
by selecting 

New

in the 

Active Zone

column of 

System4

Configuration Application's Action table

.

The 

Active Zone Setup Application

allows the user to mark an

active zone and save the information in 

*.azs

files. An active

zone is an area of the camera's view for which motion detection
is enabled and appears in red on the display grid.  Unless
changed by the user, the default filename uses the current
camera name as defined in the 

Camera Configuration

section of

the 

System4

Configuration Application

.  

NOTE:

If the user changes the camera name at a later date, the

filename does not change.

6.2

Active Zone Display Grid

The display area is split into a 16x16 grid. The grid lines are displayed by default. Initially, all the individual motion detection
zones (grids) are marked inactive. An active zone consists of several motion detection zones (grid squares) that are marked active
(red sections in the figure above).

■

You can select a set of zones by depressing the left mouse button. As the mouse is moved, a dotted rectangle is drawn to show
the selected range of motion detection zone grids. When the left mouse button is released, the area covered by the dotted
rectangle toggles the state from the inactive to active, or active to inactive. You can also click on individual grid positions to
toggle the state.

NOTE:

Any change with the active zone on your PC is not updated in your 

System4

Multiplexer until the information is saved

and downloaded to the multiplexer.

LTC 2650 S

YSTEM

4 M

ULTIPLEXER

 GUI

A

CTIVE

 Z

ONE

 A

PPLICATION

Active Zone Application Window

Summary of Contents for System4 LTC 2650/00













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands