Peg-Perego Viaggio0+1, Instructions For Use Manual

Page: 28 / 124

28
1C (Fig.B).
24•
Use in Group 0+ mode:
To determine the best
shoulder strap position, bear in mind that the child’s
shoulders must be just above the shoulder strap guides.
25•
IMPORTANT: The straps must not be too high or
too low with respect to the child’s shoulders.
26• WARNING: Do not use the car seat in Group 1 mode
with the casing extracted.
27•
Use in Group 1 mode:
To determine the best shoulder
strap position, bear in mind that the child’s shoulders
must be just below the shoulder strap guides.
28•
IMPORTANT: The straps must not be too high or
too low with respect to the child’s shoulders.
29• IMPORTANT: The “Viaggio 0+1 Switchable” car seat
can be reclined into 5 different positions only when it
is used in Group 1 mode.
To recline the car seat, press the lever under the
seat (Fig.A) and pull to adjust the seat to the desired
position (Fig.B).
How to remove the soft cover
To remove the soft cover of the “Viaggio 0+1
Switchable” car seat:
• Remove the booster cushion, where present (point 20).
• Unfasten the harness (point 13).
• Open the rear panel.
30• Unfasten the straps from the rear latch plate.
31• Unfasten the straps on the rear and slip them out from
the front.
32• Unfasten the shoulder pads from the rear and slip
them off the straps from the front.
33• Slip off the adjuster strap (Fig. C) and then remove the
headrest cover from above (Fig. D).
34• Release the crotch strap from below the body (Fig. E) and
slide the strap out through the crotch strap cover (Fig. F).
35• Slip the strap out through the opening in the soft cover
and remove the soft cover, as shown in the figure.
Soft cover maintenance
Brush the fabric parts to remove dust.
• Before placing the soft cover in the washing machine,
slide the foam rubber cushion out of the booster seat
from the rear.
17• Lock the harness by overlapping the tongues and
inserting them into the buckle of the crotch strap until
they click into place.
18• The child is now sitting correctly with the harness
fastened properly.
19• Finally, tighten the shoulder straps until they are snug
to the child’s body by pulling the central adjustment
strap towards you, as shown in the figure, taking care
not to over-tighten the straps.
IMPORTANT: Leave minimal slack (the space of
a finger) between the strap and the child's chest.
20• To slacken the straps, press the button at the centre
of the car seat and at the same time pull the straps
towards you.
IMPORTANT: Take hold of the straps under the
shoulder pads and pull, as shown in the figure.
21• The car seat has a booster cushion which is only
suitable for small babies. When the child is older,
remove the booster cushion.
• To remove the booster cushion, unfasten the seatbelts,
slide them off the booster cushion and slide the crotch
strap out through the slot in the booster cushion.
IMPORTANT: The booster cushion must be
removed when the “Viaggio 0+1 Switchable” is
used as a Group 1 car seat.
How to adjust the height of the headrest
The headrest must be adjusted to match the child’s
height. There are 7 positions.
22• To change from a lower position to a higher one: pull
the tongue in the upper central part of the headrest
upwards. The headrest will move at the same time.
To change from a higher position to a lower one: pull
the tongue in the upper central part of the headrest
upwards and, at the same time, push the headrest
down to the desired position.
When you have finished, try moving the headrest
to check it is properly locked into place.
23•
WARNING:
Do not use the car seat in Group 0+ mode
without first extracting the casing, as shown in point 1
A-B (Fig.A).
WARNING:
Do not use the car seat in Group 0+ mode
without first reclining the backrest, as shown in point
• When washing, closely follow the instructions stated on
the label sewn into the cover.
• Do not use chlorine bleach.
• Do not iron.
• Do not dry clean.
• Do not remove stains with solvents.
• Do not tumble dry.
How to replace the soft cover of the
“Viaggio 0+1 Switchable” car seat
To replace the soft cover of the “Viaggio 0+1
Switchable” car seat:
36• From below, slip the straps back in through the
opening in the fabric (Fig. A).
• Reinsert the crotch strap into the soft cover (Fig. B).
37• Fasten the crotch strap back onto the body.
38• Fasten the tongue to the crotch strap opening.
39• Put the soft cover in place, starting at the seat and moving
upwards, paying attention to the sides of the backrest.
40• Slip the soft cover over the headrest, ensuring the red
tongue passes through the opening in the fabric.
41• Insert the straps through the soft cover, starting with
the buckles.
42• Lengthen the straps and insert them through the body
of the car seat (the straps in the upper hole and the
buckles in the lower one).
43• Fasten them correctly on the rear, as shown in the figure.
• Fasten the harness at the front (point 17).
IMPORTANT: The straps must not be twisted.
44•
ATTENTION: The central adjustment strap must pass
between the body and the plastic shield, as shown.
45• Open the rear panel and fasten the straps onto the rear
latch plate.
• Fasten the straps from the front (point 16).
• For infants and for use in Group 0+ mode, reposition
the booster cushion.
Accessories
46• Clima Cover Car Seat: washable cover in Tencel,
a natural heat-regulating fiber that regulates body
moisture (warm in winter and cool in summer) (Fig. A).
• Travel Bag Car Seat: practical travel bag that keeps the