Diagnostic Control Panel Messages Reference
C-3
3610-A2-GB91-90
July 1999
Health and Status
The format of the messages is shown below:
F1
H/S: hhh:mm:ss *
Message
F2
F3
When the DDS circuit is the active link, the first line
displays a running normal-operation timer (in hours,
minutes, seconds). If there is more than one message, a
right arrow indicator (
→
) is displayed; if there is NMS
activity, an asterisk ( * ) is displayed. When a fault is
reported, the second line of the health and status screen
displays a message.
Table C-4 lists all the Device (Devic) health and status
messages that can appear, and describes the condition that
caused the fault to be reported.
Table C-5
lists and
describes the same for the Expanded (Expan) health and
status messages, while
Table C-6
lists and describes the
same for the Subnetwork (Subn) health and status
messages.
Table C-7
provides Multipoint Backup progress
messages.
Table C-4
(1 of 5)
Device Health and Status Messages
Message
Condition
CMI Fac Alarm
Backup on CMI configuration option is enabled and control mode idle (CMI) is
being received.
Config Corrupt
Configuration is corrupt. Reset all configuration options as described in
Chapter 6
of this guide. Select from one of the factory-loaded option sets
(FacC, FacT, or FacB).
DBM:Device Fail
Internal failure in the DBM detected.
DBM:Disable
DBM transmitter is disabled. DBM is in Idle mode, but no calls can be initiated
or answered.
DBM F:
alarm
A Switched 56 DBM alarm;
alarm is one of the following network alarms:
Bipr Viol
—
Excessive Bipolar Violations.
No Signal
—
No signal has been received.
The 4-wire Switched 56 DBM reports a
No Signal condition
when there is no connection to the Switched 56 kbps
network.
The 2-wire Switched 56 DBM reports a
No Signal when there
is no low-level synchronization of control data. To disable the
reporting of the
No Signal alarm, disable the DBM
(Switched 56 DBM only).
Out-of-Servc —
Out-of-Service condition (4-wire Switched 56 DBM only).
FDHP Lost
—
High-level communication over the signaling channel switch
has been lost (2-wire Switched 56 DBM only).
Summary of Contents for COMSPHERE 3610
