Paradyne ACCULINK 3160 Operator'S Manual Download Page 221 | Manualshive

Page: 221 / 296

background image

SNMP MIB Objects

E-9

3160-A2-GB21-80

March 1999

Interface Group – Input Counters (objects ifEntry 10 to ifEntry 15)

These objects collect statistics on the data received by the COM port, the AUX
port, and the MODEM port when these ports are configured as SNMP
management links. For interfaces that are not configured as an SNMP
management link, these statistics are not provided and an error status is returned
if access is attempted. The objects used to collect input statistics are listed below:

ifInOctets (ifEntry 10)

ifInUcastPkts (ifEntry 11)

ifInNUcastPkts (ifEntry 12)

ifInDiscards (ifEntry 13)

ifInErrors (ifEntry 14)

ifInUnknownProtos (ifEntry 15)

Interface Group – Output Counters (objects ifEntry 16 to ifEntry 21)

These objects collect statistics on the data received by the COM port, the AUX
port, and the MODEM port when these ports are configured as SNMP
management links. For interfaces that are not configured as an SNMP
management link, these statistics are not provided and an error status is returned
if access is attempted. The objects used to collect output statistics are listed
below:

ifOutOctets (ifEntry 16)

ifOutUcastPkts (ifEntry 17)

ifOutNUcastPkts (ifEntry 18)

ifOutDiscards (ifEntry 19)

ifOutErrors (ifEntry 20)

ifOutQLen (ifEntry 21)

«
...
219
220
221
222
223
...
»

Summary of Contents for ACCULINK 3160









































































































































































































































































































Reviews:

No comments

Related manuals for ACCULINK 3160

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 30

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Maestro E220 Series

Brand: Lantronix Pages: 25

Brand: Draytek Pages: 8

Brand: WHOOP Pages: 26

Brand: IBA Pages: 33

EdgeLens INT10G8LR56

Brand: Garland Pages: 30

Brand: ZyXEL Communications Pages: 116

Brand: Buffalo Pages: 2

DataPlot CB1224

Brand: B-G Instruments Pages: 4

HHM Series HHM2409

Brand: TDK Pages: 2

Elinx EIR510 Series

Brand: B&B Electronics Pages: 2

Brand: Casablanca Pages: 13

Brand: Maipu Pages: 26

Brand: Tripp Lite Pages: 3

Power System S914

Brand: IBM Pages: 48

Brand: Lantronix Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands