Paradyne ACCULINK 3160 Operator'S Manual Download Page 15

Page: 15 / 296

About This Guide

3160-A2-GB21-80

March 1999

Reference Documents

AT&T Technical Reference 54016

AT&T Technical Reference 62411

ANSI T1.403-1989

Industry Canada CS-03

CSA-22.2 No. 950

Industry Canada (ICES)-003

FCC Part 15

FCC Part 68

UL 1950

Management Information Base for Network Management of TCP/IP-Based
Internets: MIBII. RFC 1213, March 1991

Definitions of Managed Objects for the DS1 and E1 Interface Types.
RFC 1406, January 1993

Definitions of Managed Objects for RS-232-like Hardware Devices.
RFC 1317, April 1992

Extensions to the Generic-Interface MIB. RFC 1229, May 1991

Summary of Contents for ACCULINK 3160









































































































































































































































































































Search results

Summary of Contents for ACCULINK 3160

Reviews:

Related manuals for ACCULINK 3160

Brands by name

Popular brands

Paradyne ACCULINK 3160, Operator'S Manual

Search results

Summary of Contents for ACCULINK 3160

Reviews:

Related manuals for ACCULINK 3160

Brands by name

Popular brands