Panasonic Section 700 Technical Manual Download Page 19

Page: 19 / 311

ICX-35-700

ICX (International), issued March/1998

Chapter 3. System Features

System Features are either available on a system-wide basis or aid in the overall administration of the
System.

This chapter contains detailed descriptions of the following System Features:

Topic

Page

AEC Disconnect

Attendant Groups

Automatic Call Distributor

Automatic Route Selection

Automatic Trunk to Trunk Transfer

Background Music/MOH Separation

Battery Backup

Building Block Expansion Capability

Built-In Voice Mail

Call Progress Tones

Caller ID

Caller ID Alpha Tagging (Not Available in USA)

Centrex/PBX Compatibility

Class of Service

Class of Service - Trunk/Tie

Class of Service - Ext/Ext Restriction

Class of Service - Extension Feature

Class of Service - Trunk to Trunk Restriction

Class of Service - Extension (Station) Timers

Computer Telephony Integration Capability (USA Only)

Data Security

Day/Night System Mode

Manual Day/Night Mode

Automatic Day/Night Mode

Digital Pad

Direct Inward System Access

Digital Key Telephones

Analog Device Capability

Summary of Contents for Section 700
























































































































































































































































































































Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands

Panasonic Section 700, Technical Manual

Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands