background image

Section 700 - Operation

Chapter 5. Key Telephone Features

ICX-35-700

ICX (International), issued March/1999

 171

Hardware Requirements

N/A

Considerations

N/A

MCO Appearances

Description

You can make and receive trunk calls using an MCO key. Each extension can have up to 5 MCO keys. 

An MCO key can be assigned to any of the pooled trunk groups. Pressing the MCO key is the same as 
dialling the MCO Access Code (usually 9 [UK/HK], 0 [Taiwan, Malaysia, Indonesia], or 81-84 by 
default).

Operation

Considerations

Press the MCO key that flashes red to answer an outside call.

If you are already on a call appearing on an MCO key and you press another MCO key, a line on 
the other MCO key is selected and the first call is dropped.

If a trunk key is assigned, the trunk key LED will light when that specific trunk is used instead of 
the MCO key LED.

To place a call on System Trunk Hold (page 133)...

1.   Press the HOLD key.

To transfer a call...

1.   Press the HOLD key.

2.   Dial the destination extension.

3.   Press the PROG key.

Operation

Action

To originate a trunk call

Press an idle MCO key.

The key blinks (green) as the call is made.

To receive a call on an MCO key.

If ringing line preference is enabled, go off-hook. 
If ringing line preference is not enabled, go off-
hook and press the MCO key with the green 
flashing LED.

The LED lights solid green.

To place a call on Exclusive trunk Hold

Press the MCO key. 

The key flashes green while the call is held.

To place a call on System Trunk Hold

Press the HOLD key.

The key flashes green while the call is held.

To transfer a call

Press HOLD, dial the destination extension, then 
press PROG (if on-hook transfer is off) or go on-
hook.

Operation

Action

Summary of Contents for Section 700
























































































































































































































































































































Reviews: