Panasonic Section 700 Technical Manual Download Page 298

Page: 298 / 311

298

ICX (International), issued March/1999

ICX-35-700

Chapter 7. SLT Features

Section 700 - Operation

Hardware Requirements

•

N/A

Considerations

•

The same Walking TRS (Call Barring) COS code can be used on more than one extension.

•

Walking TRS (Call Barring) COS mode is kept until the user goes on-hook.

•

ARS and TRS (Call Barring) dialling privileges follow the Walking TRS (Call Barring) COS.

•

Before entering a new Walking TRS (Call Barring) COS code, you must first clear the existing
code.

•

When Walking TRS (Call Barring) COS is used, Wxxxx (where xxxx is the user’s extension
number) appears in Call Logging.

Summary of Contents for Section 700
























































































































































































































































































































Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands

Panasonic Section 700, Technical Manual

Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands