Panasonic Section 700 Technical Manual Download Page 213

Page: 213 / 311

Section 700 - Operation

Chapter 6. DSLT Features

ICX-35-700

ICX (International), issued March/1999

213

Hardware Requirements

•

An Call Logging printer or external call accounting system is required to collect account code
records.

Considerations

•

Account codes are not available during conversation recording mode for the Built-In Voice Mail.

•

Even though up to 10 digits may be entered, the system verifies the ID based on the first 4 digits
only.

•

Account codes will be cancelled after using trunk queuing.

•

Account Codes interact with TRS (Call Barring) as shown in the following table:

Attendant Group Calls

CPC-96, CPC-288, and CPC-576 All Versions

Description

You can call the attendant group from any extension by dialling the designated attendant number.

3. Enter the Account Code (10 digits).

4. Press a vacant CO Trunk key or enter a trunk access code

(default = 9 [UK/HK], 0 [Taiwan, Malaysia, Indonesia], or
81-84).

5. Dial the phone number.

Forced or Not Forced

Verified or

Non-Verified

TRS (Call Barring) Class

No Account Entry

Account Entry

Not Forced

Non-Verified

Extension Port Based TRS

Class

Extension Port Based TRS

Class

Verified

Account Code Based TRS

Class

Forced

Non-Verified

TRS Class for Forced

Account Code

(FF1 0 19 0001)

Extension Port Based TRS

Class

Verified

Account Code Based TRS

Class

Action

Result

Summary of Contents for Section 700
























































































































































































































































































































Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands

Panasonic Section 700, Technical Manual

Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands