Indicator status
Projector status
Off
The power plug is not connected to the outlet.
Red
Lit
The power is switched off (in standby mode).
Projection will start when the power <
v
/
b
> button is pressed.
f
The setting of the projector is as follows.
g
The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO]
f
When the light source indicator <LIGHT> or the temperature indicator <TEMP> is blinking, the projection
will not start even if the power <
v
/
b
> button is pressed. (
x
page 135)
Blinking
*1
The power is switched off (in standby mode).
Projection will start when the power <
v
/
b
> button is pressed.
f
The standby power consumption is high. The projector is set as follows
g
The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NORMAL]
and any one or both of the following setting is met.
g
The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [QUICK STARTUP] is set to [ON]
g
The [PROJECTOR SETUP] menu → [AUDIO SETTING] → [IN STANDBY MODE] is set to [ON]
f
The indicator will change to a red light when the specified time has elapsed after the projector enters the
standby mode if the projector is set as following.
The specified time is a time set in the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [QUICK
STARTUP] → [VALID PERIOD].
g
The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [QUICK STARTUP] is set to [ON]
g
The [PROJECTOR SETUP] menu → [AUDIO SETTING] → [IN STANDBY MODE] is set to [OFF]
f
When the light source indicator <LIGHT> or the temperature indicator <TEMP> is blinking, the projection
will not start even if the power <
v
/
b
> button is pressed. (
x
page 135)
Blinking
*2
The power is switched off (in standby mode).
Projection will start when the power <
v
/
b
> button is pressed.
f
The standby power consumption is high. The projector is set to the following settings.
g
The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NORMAL]
g
The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [QUICK STARTUP] is set to [OFF]
g
The [PROJECTOR SETUP] menu → [AUDIO SETTING] → [IN STANDBY MODE] is set to [OFF]
f
When the light source indicator <LIGHT> or the temperature indicator <TEMP> is blinking, the projection
will not start even if the power <
v
/
b
> button is pressed. (
x
page 135)
Green
Lit
Projecting.
Blinking
*3
The light source is turned off due to the [POWER MANAGEMENT] setting.
The projector lights up and begins to project when a signal is input or a button operation is performed.
f
The setting of the projector is as follows.
g
The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [POWER MANAGEMENT] is set to
[READY].
Blinking
*4
The light source is turned off
because the shutter function is in use (shutter: closed).
The projector lights up and begins to project when you press the <SHUTTER> button on the remote control
or the control panel.
Orange
Lit
The projector is preparing to be switched off.
The power will be switched off after a while. (Changes to the standby mode.)
*1 The indicator
flashes
in the cycle:
0.5 seconds (light) → 0.5 seconds (off)
*2 The indicator
flashes
in the cycle:
2.75 seconds (light) → 0.25 seconds (off)
*3
The indicator flashes
in the cycle:
2.0 seconds (light) → 2.0 seconds (off)
*4
The indicator flashes in the cycle: 0.75 seconds (light) → 0.75 seconds (off)
Note
f
While the power indicator <ON (G)/STANDBY (R)> lights orange, the fan is running to cool the projector.
f
For approximately five seconds after the projector is turned off, the indicator does not light up even if the power is turned on. Turn on the
power again after the power indicator <ON (G)/STANDBY (R)> lights/blinks red.
f
The projector consumes power even in standby mode (power indicator <ON (G)/STANDBY (R)> lights/blinks red). Refer to “Maximum power
consumption” (
x
page 153) for the power consumption.
f
The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
42 -
ENGLISH
Chapter 3 Basic Operations - Switching on/off the projector