Panasonic PT-TMZ400, Operating Instructions Manual

Page: 67 / 161

Note
f
[LIGHTS OUT SIGNAL LEVEL] cannot be set when [LIGHTS OUT TIMER] is set to [DISABLE].
f
When [LIGHTS OUT TIMER] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on again
from the state that the light source has turned off by this function.
g
When the brightness level of the image signal being input has exceeded the value set in [LIGHTS OUT SIGNAL LEVEL]
g
When the input signal is gone
g
When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed
f
When the image of analog signal is projected, the image may be affected by the signal noise while the brightness level of the image signal
is detected. In such case, it is determined that the signal has not fallen below even when the brightness level of the image falls below the
value set in [LIGHTS OUT SIGNAL LEVEL].
[RGB/YC
B
C
R
] / [RGB/YP
B
P
R
]
The projector will automatically detect the input signal, but you can set the system format manually when an
unstable signal is input. Set the system format matching the input signal.
1) Press
as
to select [RGB/YC
B
C
R
] or [RGB/YP
B
P
R
].
2) Press
qw
or the <ENTER> button.
f
The [RGB/YC
B
C
R
] or [RGB/YP
B
P
R
] individual adjustment screen is displayed.
3) Press
qw
to switch the item.
f
The items will switch each time you press the button.
f
Normally it is set to [AUTO]. If it cannot project properly with [AUTO], set it to [RGB], [YC
B
C
R
] or [YP
B
P
R
]
according to the input signal.
Terminal System format
<COMPUTER 1 IN> terminal /
<COMPUTER 2 IN> terminal
480/60i, 576/50i, 480/60p, 576/50p Select [AUTO], [RGB] or [YC
B
C
R
]
Other video signals Select [AUTO], [RGB] or [YP
B
P
R
]
<HDMI IN 1> terminal /
<HDMI IN 2> terminal
480/60i, 576/50i, 480/60p, 576/50p Select [AUTO], [RGB] or [YC
B
C
R
]
Other image signals Select [AUTO], [RGB] or [YP
B
P
R
]
Note
f
For details of the image signals that can be used with the projector, refer to “List of compatible signals” (
x
page 156).
f
This may not operate properly for some connected external devices.
[RGB-SYSTEM]
(Only for analog RGB signal input)
The projector automatically detects the input signal, but the images may not be displayed properly depending on the
input signal. In that case, select the item according to the input signal.
1) Press
as
to select [RGB-SYSTEM].
2) Press the <ENTER> button.
f
The [RGB-SYSTEM] screen is displayed.
3) Press
as
to select the signal and press the <ENTER> button.
f
The selectable items differ depending on the input signal.
Items Resolution (dots)
Scanning frequency
Dot clock frequency
(MHz)
Horizontal (kHz) Vertical (Hz)
[1280x768/60] 1 280 x 768 47.7 60.0 80.1
[1366x768/60] 1 366 x 768 47.7 60.0 84.7
[1400x1050/60] 1 400 x 1 050 65.2 60.0 122.6
[1680x1050/60] 1 680 x 1 050 65.2 60.0 147.1
[1440x900/50] 1 440 x 900 46.3 50.0 87.4
[1600x900/50] 1 600 x 900 46.3 50.0 97.0
[1440x900/60] 1 440 x 900 55.9 60.0 106.5
[1600x900/60] 1 600 x 900 55.9 60.0 119.0
[1024x768/50] 1 024 x 768 39.6 50.0 51.9
[1280x768/50] 1 280 x 768 39.6 50.0 65.2
[1366x768/50] 1 366 x 768 39.6 50.0 69.9
[1400x1050/50] 1 400 x 1 050 54.1 50.0 99.9
[1680x1050/50] 1 680 x 1 050 54.1 50.0 120.2
ENGLISH - 67
Chapter 4 Settings - [PICTURE] menu