manualshive.com logo in svg

Panasonic MN103001G/F01K, User Manual

Share
Download
Panasonic MN103001G/F01K User Manual Download Page 353

Serial Interface

13-51

■

When a reception error is generated

•

Transfer with 7-bit data length, parity on, and 2 stop bit

Fig. 13-4-7   Timing Chart (22)

When "reception end" is set as the reception interrupt source, an interrupt request is generated when reception ends,

regardless of whether or not an error occurred.
When "reception end with error" is set as the reception interrupt source, an interrupt request is generated when

reception ends with an error having occurred.  (An interrupt request is not generated at the moment that the error
occurred.)

An overrun error is generated when reception of the next data is completed before previously received data is read
from the SC3RXB.  In this event, the previously received data is lost.  The overrun error indicator flag (SC3OEF)

is updated at the moment the final data bit is received.
A parity error is generated when 0-fixed parity is set and a "1" is received, when 1-fixed parity is set and a "0" is

received, when even parity is set and an odd number of ones is received, or when odd parity is set and an even
number of ones is received.  The parity error indicator flag (SC3PEF) is updated at the moment the parity bit is

received.
A feaming error is generated when "0" was received for the stop bit. The framing error indicator flag (SC3FEF) is

updated at the moment the stop bit is received.

■

Transmission interruption function

SC3TWS and SC3TWE in the SC3CTR serial 3 control register can be used to interrupt and resume transmissions

according to the status of external pin IRQ7.
A transmission is interrupted by masking the transmission end or transmission buffer empty interrupt.

The specifications of this microcontroller prohibit the writing of data to the transmission buffer when the interrupt
signal is masked through external pin control.

SP

bp1

bp2

bp3

bp4

bp5

bp6

PTY

bp0

ST

SP

“H”

SC3RXF flag

SBI pin

SC3RBF flag

SC3OEF flag

SC3PEF  flag

SC3FEF flag

Interrupt request

Summary of Contents for MN103001G/F01K



















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands