manualshive.com logo in svg

Panasonic MN103001G/F01K, User Manual

Share
Download
Panasonic MN103001G/F01K User Manual Download Page 314

Serial Interface

13-12

<Reception>

• One-byte transfer with 8-bit data length and parity on

Fig. 13-2-5   Timing Chart (3)

• Two-byte transfer with 8-bit data length and parity off

Fig. 13-2-6   Timing Chart (4)

After reception end (when the SC0RBF flag is "1"), the received data is fetched by reading the SC0RXB.

 In the case of a 7-bit transfer, the MSB (bit 7) is "0".

The SC0RXF flag is set to "1" at the start of reception (at the falling edge of SBT pin ), and is set to "0" at the end
of reception.

The SC0RBF flag is set to "1" at the end of reception, and is set to "0" when SC0RXB is read.

Sending dummy data makes it possible to receive data while supplying the clock from the microcomputer side.  In
this case, interrupt requests are also generated by the transmission source.  Receive data according to the following

procedure:
(1) Select the internal clock as the reference clock, and set the parity, character length, etc.

(2) Enable both the transmission operation and the receiving operation.
(3) When dummy data is written to the transmission buffer, the clock is sent and reception begins.

When using clock synchronous mode (2), set the SBO pin as a general-purpose input port before writing the
dummy data to the transmission buffer, and then reset the pin as the SBO pin after transmission is complete.

bp1 bp2 bp3 bp4 bp5 bp6

bp0

SBI pin

SBT pin

Interrupt request

SC0RXF flag

SC0RBF flag

Data read

bp1 bp2 bp3 bp4 bp5 bp6

bp0

bp7

bp7

bp1

bp2

bp3

bp4

bp5

bp6

bp7

bp0

SBI pin

SBT pin

Interrupt request

SC0RXF flag

SC0RBF flag

Data read

PTY

Summary of Contents for MN103001G/F01K



















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands