background image

• Thank you very much for your 

purchase of Panasonic product.

• Please read this instruction 

manual carefully for proper use.

• In particular, be sure to read 

Safety precautions (P.2 to P.7) 
before use for safety.

• Keep this manual with care after 

reading, and read as necessary.

• This product is for industrial use 

only and can not be used for 
other uses eg home use.

Technical Instructions

Brushless motor / Brushless amplifier

MINAS-BL  GU series

 Be sure to give this Instruction manual to an end user.

Safety precautions ......................................2

Introduction / Checking the model ..............8

Checking the model ....................................8

Name of part .............................................10

Installation ................................................12

Caution .....................................................15

System configuration and wiring...............16

Wiring .......................................................18

Test run .....................................................24

Checking load and use condition  ................28

Assembling of gear head ..........................30

Maintenance/ inspections .........................31

Protective functions ..................................32

How to clear trip........................................34

Troubleshooting ........................................35

How to use Digital key pad (option) ..........38

    Operating instruction  ...........................40

    Test run (Digital key pad) ......................41

    How to copy parameter ........................44

    List of parameters (Default) ..................47

    LED display ..........................................51

    The function of parameters ...................52

Outline of PANATERM for BL ...................63

Example of operation pattern ...................63

Conformance to EC directive and UL standard ...64

Specifications ...........................................68

Options .....................................................74

List of peripheral equipments ...................78

Cautions for proper use ............................79

After-sale service (Repair)  .........Back cover

 

page

 

page

<Contents>

• Label of safety precaution is affixed to the product.

Summary of Contents for MINAS-BL GU series










































Reviews: