background image

Result Message

Description

Applicable Screens

Complete

The operation has successfully completed.

All screens except

4.6.7  Export Phonebook

Failed (Parameter Error)

The operation failed because:

Some specified values are out of range
or invalid.

All screens

Failed (Memory Access
Failure)

The operation failed because:

Access error to the flash memory
occurred while reading or writing the
data.

All screens

Failed (Transfer Failure)

*1

The operation failed because:

A network error occurred during the
data transmission.

All screens

Failed (Busy)

The operation failed because:

The unit is in an operation that
accesses the flash memory of the unit.

All screens

When attempting to import/export the
phonebook data, the unit is on a call.

While transferring the phonebook data,
a call arrived at the unit.

4.6.6  Import Phonebook
4.6.7  Export Phonebook

When updating the firmware, the unit is
on a call.

4.7.2  Local Firmware
Update

Failed (Canceled)

The operation failed because:

While transferring the phonebook data,
IP Reset was performed on the unit.

4.6.6  Import Phonebook
4.6.7  Export Phonebook

While transferring the firmware file, IP
Reset was performed on the unit.

4.7.2  Local Firmware
Update

While transferring the phonebook data,
the connection with the unit was
interrupted.

4.6.6  Import Phonebook
4.6.7  Export Phonebook

Failed (Invalid File)

The operation failed because:

The imported UTF-16 text file has an
invalid BOM (Byte-order Mark).

4.6.6  Import Phonebook

The firmware file is corrupted or invalid.

4.7.2  Local Firmware
Update

Failed (File Size Error)

The operation failed because:

The size of the imported phonebook is
too large.

4.6.6  Import Phonebook

The size of the firmware file is
insufficient.

4.7.2  Local Firmware
Update

Failed (Busy)

The operation failed because:

When attempting to import/export the
phonebook data, the connection with
the unit has been disconnected.

4.6.6  Import Phonebook
4.6.7  Export Phonebook

Document Version    2011-06

Administrator Guide

25

1.1.6 Web User Interface Programming

Summary of Contents for KX-UT133-B









































































































































































































































































Reviews: