6
$2
Auxiliary Control Input Connector
[AUX CONTROL IN] (8-pin DIN Connector)
External control signals are input to this connector in controlling the head’s pan/tilt, lens zoom, focus and iris operations.
Note: In externally controlling the pan/tilt head and lens through this connector, set IRIS LEVEL Control
@6
on this control panel
to the centre point (straight up), and do not simultaneously operate SPEED Switch
@9
, ZOOM Lever
#6
, FOCUS Lever
#7
,
and PAN/TILT Lever
#8
. Operation errors may occur if external controls are simultaneously used.
1 +5V
2 ZOOM
3 FOCUS
4 TILT
5 PAN
6 GND
7 SPEED
8 IRIS
Ground GND
1
2
3
4
6
7
Ground
5
8
Example of auxillary
control circuit
Note: Make sure that the lens and pan/tilt head stop
at the center point of the zoom, focus, pan and tilt controls
(or at the lever reset position if the controls have a lever reset function).
Iris control
Zoom
control
Pan
control
Tilt
control
Focus
control
SPEED switch
100
Ω
10K
Ω
10K
Ω
10K
Ω
10K
Ω
6.8K
Ω
20K
Ω
6.8K
Ω
100
Ω
100
Ω
100
Ω
8-pin DIN connector
pin assignment
(as viewed from the
rear of the control panel)
$3
VIDEO Input Connector
[TO CAMERA PAN/TILT HEAD, VIDEO IN]
(BNC Connector)
Connect it to the video output connector [VIDEO OUT]
on the pan/tilt head with a coaxial cable (5C-2V or
equivalent), which may be extended up to 500 meters.
$4
Genlock Output Connector
[TO CAMERA PAN/TILT HEAD, G/L OUT]
(BNC Connector)
Connect it to the G/L input connector [G/L IN] on the
pan/tilt head with a coaxial cable (5C-2V or equivalent)
in operating the camera in external sync mode. The
cable can be extended up to 500 meters.
$5
Camera Control Output Connector
[TO CAMERA, PAN/TILT HEAD CAMERA CONTROL
OUT] (BNC Connector)
Connect it to camera control input connector [CAMERA
CONTROL IN] on the pan/tilt head with a coaxial cable
(5C-2V or equivalent), which may be extended up to
500 meters.
$6
Pan/tilt Control Output Connector
[TO CAMERA PAN/TILT HEAD, PAN/TILT CONTROL
OUT] (RJ-45 8-pin Modular Jack)
Connect it to pan/tilt control input connector [P/T CON-
TROL IN] on the pan/tilt head with a 10BASE-T straight
cable (UTP category 5 or equivalent), which may be
extended up to 500 meters.
$77
Video Output Connectors
[VIDEO OUT 1, VIDEO OUT 2] (BNC Connector)
Video signals adjusted by the cable compensation cir-
cuit according to the cable length from the rotary head
to the control panel are output. There are two output
connectors to be connected to a monitor, special effect
generator (SEG), VTR, or other video input devices with
coaxial cables.
$8
Genlock Input Connectors
[G/L IN] (BNC Connector)
Black burst signals are input to one of the two connec-
tors in operating the camera in external sync mode.
The two connectors are automatically terminated, so
input the above signals to one of them and use the other
as a loop-through output.
$9
S-Video Output Connector
[S-VIDEO OUT] (4-pin S-Connector)
Y (luminance) and C (chrominance) signals are output.
Connect it to the S-video input on a monitor or S-VHS
VTR, for example.
