This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
!
WARNING
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns the user that uninsulated voltage within
the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that impotant literature concerning
the operation and maintenance of this has been included.
Therefore, it should be read carefully in order to avoid
any problems.
T
here are special components used in this equipment which are important for safety. These parts are indicated
by the ”
Y
” mark on the schematic diagram and the replacement parts list. It is essential that these critical
parts should be replaced with manufacturer's specified parts to prevent shock, fire, or other hazards.
Do not modify the original design without permission of manufacture.
IMPORTANT SAFETY NOTICE
[AW-RP505]
Source Voltage :
12 V DC (DC jack)
Power Consumption :
12 V, 0.5 A
Preview Video Input :
1.0 V[p-p] composite/75
Ω
(BNC connector)
Genlock Input :
black burst
75
Ω
loop through with auto terminator (BNC connector)
Preview Video Output :
1.0 V[p-p] composite/75
Ω
(BNC connector)
Genlock Output :
75
Ω
(BNC connector)
Camera Control Output :
Control signal (BNC connector)
Pan/tilt Control Output :
Control signal (RJ-45 8P modular jack)
System Tally Input :
Tally signal (6 pin Terminal block)
Auxiliary Control Input :
Control signal (8 pin DIN connector)
Switches :
Power ON/OFF Switch, CAM CONT Switch, GAIN HIGH/MID/LOW Switch,
GAIN AGC/MANU Switch, SCENE FILE Switch, CONTROL Switch, LAMP Switch,
MODE BAR/CAM Switch SHUTTER Switch, AUTO/ATW ATW Switch, AUTO/ATW A Switch,
AUTO/ATW B Switch, AWC Switch, ABC Switch, G/L PHASE ON/OFF Switch,
G/L PHASE Coarse Switch, IRIS AUTO/MANU Switch, MEMORY Switch, PRESET Switch,
DEF Switch, WIP Switch, H/F Switch, EXT Switch, ND Switch, OP Switch, SPEED Switch,
Controls :
T. PED Control, G/L PHASE SC Control, G/L PHASE H Control, IRIS LEVEL Control,
ZOOM Lever, FOCUS Lever, PAN/TILT Lever
Multiport Hub Connecting
Cable :
x 4 (Coaxial Cable 3 pcs., 10BASE-T straight cable 1 pc.)(In case of using G/L function)
Maximum cable length :
10 m (In case of using coaxial cables 5C-2V and 10BASE-T straight cable UTP category-5)
Operating temperature :
−
10°C to +45°C (14°F to +113°F)
Dimensions :
210 (W) x 88 (H) x 177 (D) mm [8-1/4" (W) x 3-1/2" (H) x 7" (D)]
Weight :
2.2
kg
(4.9 lbs.)
Finish :
AV Ivory painting
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
ACCESSORIES
Seal ........................................................ 1
Mounting screws ......................................... 12
Rack angle .............................................. 2
M4 x 8mm .............................................. 8
Connect plate.......................................... 1
M5 x 8mm .............................................. 4
