Pacific energy TOFINO i30s Installation Instructions Manual Download Page 18

Page: 18 / 44

Ceramic glass

bafﬂe

Front bafﬂe
support

Rear ceramic
glass bafﬂe
& rear panel
support posts

Figure 30: Ceramic glass bafﬂe.

Figure 31: Inserting bafﬂe into the upper corner.

Figure 32: Raising bafﬂe above front support.

Figure 33: Sliding bafﬂe over to rest on top of supports.

Bafﬂe

The bafﬂe is made of ceramic glass which allows for the use of a halogen lamp feature. The halogen lamp is

only available on units using the SIT Proﬂame conﬁguration, the Maxitrol conﬁguration does not include the
use of a halogen lamp.

Installing the ceramic baffle:

1. With the door removed, place one end of the bafﬂe over one of the two upper corners so that the bafﬂe

is resting on a rear peg and a front support (Figure 31).

2. Raise the opposite end of the bafﬂe so that it is raised above the supports on the other side of the ﬁre-

box (Figure 32).

3. Slide the bafﬂe over so that it is supported by all four supports (Figure 33).

Cleaning the ceramic glass baffle:

Note: Do not clean the ceramic glass bafﬂe until the ﬁreplace has been turned off long enough for the glass
door and ceramic bafﬂe to sufﬁciently cool down. Use glass cleaner to clean the ceramic bafﬂe of soot or
other debris.

130717-44 5055.990-A

i30 TOFINO

Summary of Contents for TOFINO i30s













































Search results

Summary of Contents for TOFINO i30s

Reviews:

Related manuals for TOFINO i30s

Brands by name

Popular brands

Pacific energy TOFINO i30s, Installation Instructions Manual

Search results

Summary of Contents for TOFINO i30s

Reviews:

Related manuals for TOFINO i30s

Brands by name

Popular brands