background image

53

EH-800 connections

1

2

3

4

5

Installing the outdoor sensor:

Position the outdoor sensor (TMO) in a shady pla-

ce on the northern side of the building at a height of 

about 2.5 meters. Do not install the sensor directly 

above a window, door, vent or sensor cable protecti-

on tube coming from indoors, or next to an exhaust 

duct or any other source of heat. If necessary, the 

cable can be either shortened or lengthened using a 

screw connector. (No special requirements for cab-

le type). The controller uses an outdoor temperatu-

re setting of 0° C if the outdoor sensor has not been 

connected.

Connect the cord and connecting box if you 
take something that is not included in the basic 
package into use :

The cord and connecting box can be used to connect 

2 different things (measurements 3 and 4).  Open the 

connecting box and make the necessary connections  

(see page 23-25).

Connecting the power source:

Plug one end of the cord into the wall and the oth-

er end into the controller. We recommend putting 

the cord in a protective sleeve. Put the connec-

tion space’s protective cover back into place.

24V

AC/DC

power supply

outdoor

sensor

cord and

connection box

Is attached to the controller

Connected to the controller’s RJ45-2 

using the extension unit (meas. 5)

H1 Supply water sensor

H2 Supply water sensor

Cut the corner of the bag open and squee-

ze the grease on the bottom surface of the 

sensor on the copper plate. 

Wrap the fastening strap around the pipe. 

Make sure that the surface sensor is not 

loose.

Wrap the strap around the pipe again if it 

is long enough. Cut the strap to the pro-

per length along the groove between the 

holes.

Detach the protective cover of the controller’s connection 

space (slides off at a right angle to the controller) and connect 

the outdoor sensor to the controller. 

Power source          

GSM modem 

and EXU-800

extension unit 

connection 

(see separate 

instructions)

Cord and 

connect. box 

Outdoor sensor 

(meas. 3 and 4) 

24 V

 AC/DC

Installing the supply water sensor on the pipe:

Fasten the surface sensor to the surface of the pipe entering 

the network about 0.5...1.5 m from the valve either on the top or 

side of the pipe.  The surface of the pipe should be clean, rust 

free and smooth; the pipe can be painted.

Summary of Contents for EH-800





























































Reviews: