background image

16

Relay control   

Two different temperatures are compared, e.g., the temperatures of the solar collector and ac-

cumulator.   When the temperature difference is large enough, e.g., 10 °C, the solar collector’s 

circulating pump is switched on. When the temperature difference drops to, e.g., 3 °C, the cir-

culating pump is switched off.  

Relay control is switched on (ON) when the valve opens to the set setting. Relay control is 

switched off when the valve position is at the OFF setting. The present actuator position and 

relay mode can be seen from the controller’s display. 

Select the energy mode according to H1 control valve’s control information. 

Relay use

Explanation

Other controls -> Relay control

   > Other controls > Relay control

Relay control           Accord.  to  H1  valve position    

Control mode                                               Automatic>
Valve position where  relay is active            95%  > 
Valve position where relay is released        90%  >
H1  Valve position                                                    85%
Relay control mode                                                       OFF

   > Other controls > Relay control

Relay control        Accord. to the temp.  difference     

     

Control mode                                                      Automatic>
Temp. of solar collector  (A)                                   68.3°C  >
Temperatur of accumulator  (B)                             55.4°C >
Temp. diff.  (A-B) where relay is active                10 °C   >  
Temp.diff. (A-B) where relay is released              3 °C   > 
Relay control mode                                                              ON

Relay control according to the temperature difference:

Relay control according to the H1 Valve position:

Example: The water in the boiler is first warmed using inexpensive energy (e.g., air-to-water heat 

pump) When EH-800 has almost completely opened the control valve (e.g., 95%) the relay is activa-

ted (ON) and the oil burner receives a running permit. When the heating need decreases the control-

ler starts closing the valve. The oil burner’s running permit is inactivated when the valve has closed 

to the point at which the relay switches to the OFF mode (e.g., 90%).   

0 %

100%

90%         95%

Valve position

Oil burner

running permit

Relay ON

Relay OFF

   Other controls > Relay control

Relay control                                                General alarm    

     

Relay control mode                                                         OFF

When any of the alarms is activated in the device, also the sum/common alarm is activated. 

The common alarm does not indicate, which alarm in the device is active. When any of the 

alarms is unacknowledged, the relay is active.

An example: If EH-800 is installed in a separated room, the information of the controller`s alarm can 

be transmitted to the accommodation by connecting e.g. an indicator lamp or a siren to the relay. 

When the controller alarms, the indicator lamp or the siren indicates the alarm.

General alarm:

Summary of Contents for EH-800





























































Reviews: