background image

54

EH-800 initial setup

You can change the language of the controller, set the 
time and date and select the controller use during the ini-
tial setup.  

If a room sensor or items listed below are connected to the 

controller, they can be connected here or later in the controller’s 

device settings. 

Press OK.  Select the measurement use. 

See additional information on 

p. 23-25.

 The settings of measuring channels (measurements 3 
and 4):

Changing the language: 
Press the control knob 
(=OK), turn the control 
knob to change the langu-
age and press OK.

OK

EH-800 setup

Language/Kieli/Språk 

Suomi >

Time and date setting 

 >

Using as a heating controller 

 >

Drying  a concrete floor    

>

 Language/Kieli/Språk

Using EH-800 as a heating controller

Measur. channels settings 

 >

Heating mode 

Radiator heating, normal >

Direction of valve 

Open clockwise >

Start-up with new settings 

 >

Time:

Set the hours and press OK to confirm. Set the minutes and press 

OK to confirm. 

Time and date setting:

  Time

19:44

hh:mm

Give the hours:

Kellonajan asettaminen

 Date

Ke24.02.2009

dd.mm.yyyy

Give the date:

Turn the control knob to go to time and date settings and press OK.  

Set first the time. Press OK.

1

2

3

Changing the language

If you do not take additional connections into use, go to section  4.

Date:

 

First set the day, then the month and then the year. Press OK. (the 

name of the weekday is automatically updated). Press ESC to exit 

from time and date settings.  

Measeurements

Measurement 3 

Not in use >

Measurement 4 

Not in use >

  

  Measurement 3

  Not in use

  TMR Room measurement

  TMR / SP Room temp measurement
  Return water temperature
  Temperature of accumulator
  Temperature of boiler
  Measurement 3

  Measurement 4

  Not in use
  TMR / SP Room temp. potentiometer
  Home/Away -switch
  Return water temperature
  TMR / P Room compensation
  Temperature of accumulator 
  Temperature of boiler
  Measurement 4
  Pressure alarm
  Burner alarm
  Pump alarm
  Boiler alarm

  Alarm 4

 

Suomi

  Svenska

 

English

Taking hybrid heating into use, see p. 32-33.

Summary of Contents for EH-800





























































Reviews: