background image

38

Device settings> Telecommunications settings

Message centre number             +358447983500  >

PIN 

      1234 >

Device ID                                                                            >
Alarm number 1                                 +358401111111 

>

Alarm number 2                                +358402222222  >
Text message limiting (24h)                                     30 >    

Text message settings

The controller automatically initializes the GSM modem at 10 

minute intervals. This ensures that the GSM connection will 

continue to work after power failures.

PIN: 

If the SIM card has a PIN inquiry, the controller asmks for the 

PIN.

DNA     +35844 798 3500

TeliaSonera  +35840 520 2000

Elisa          +35850 877 1010            

Saunalahti    +35845 110 0100       

Tele Finland  +35840 520 2330       

The selections that have been made appear on the display. If you 

want to make changes, press OK at the row you want to change and 

a window will open up.

Connect the GSM modem to the controller 

The EH-controller compatible GSM modem makes it possible to 

communicate with the controller via text message. If an extension 

unit has been connected to the controller’s RJ45-2, then the mo-

dem is connected to the extension unit.  

Device settings > Text message settings

Message centre numbers:

  PIN

Approve: Press OK a few seconds
Cancel: Press ESC a little file

 

Device ID

Approve: Press OK a few seconds
Cancel: Press ESC a little file

  Message center number

Approve: Press OK a few seconds
Cancel: Press ESC a little file

+

3

5

8 4 4 7 9 8 3

5 0 0

Message centre number: 

The controller can identify the operator in 

use from the modem’s SIM card. Identification occurs after the PIN 

is given. If the controller does not identify the operator even though 

the PIN is correct, write the message centre number. If you change 

the message centre number, the number is entered on the SIM card. 

The controller reads the number entered on the SIM card.   

Device ID: 

The controller can be given a device ID that functions as the 

device’s password and location. The device ID can be freely labelled. 

When communicating with the device using a mobile phone, write 

the device ID in front of the key word. Note capitals and small letters 

in the device ID. Clear the fields to take the device ID from use. 

A. Using the RJ45-2-connection            

GSMMOD5

 

RJ45-2

telecommunication

fuse 2,5A

red +

black-red -

7

 

(24 VDC OUT)

RJ45-2

Modem

RJ-45-2

B. Using the extension unit

GSMMOD5 current feed

OUMAN 

GSMMOD5

 

Extension unit

EXU-800

Summary of Contents for EH-800





























































Reviews: