Otto BCX 180, User Manual

Page: 14 / 24

14
English
Ordinary maintenance
FREQUENCY OPERATION DESCRIPTION
Every 2 weeks Threads greasing Grease the ring nut thread (2) as well as the relevant cartridge holder tube thread,
with lubricating grease. (CSG II MP 450 )
Every week Material holder tube inner
greasing Grease the material holder tube inner surface with a brush.(CSG II MP 450 )
Every 2 weeks Dusts, filth or material residues Carefully clean the front ring nut thread (2) and the relevant cartridge holder tube
thread with a clean cloth and a detergent.
Every 2 weeks Grease the transmission rod
or rods. After removing the material holder tube (CSG II MP 450 only) grease the
transmission rod or rods.
Cleaning
FREQUENCY CAUSES DESCRIPTION
On each charge Fresh material residues Always carefully remove material residues from the gun surfaces, dispose in
compliance with the applicable regulations in the country of use.
Every week Dusts or filth Carefully clean the exhaust air outlets (11.1) with a clean cloth and a detergent and
check for potential clogging.
Every 2 weeks Dusts, filth or material residues Carefully clean the front ring nut thread (2) with a clean cloth and a detergent and
the relevant thread on the cartridge holder tube. (CSG II MP 450 )
Every 2 weeks Dusts or filth Carefully clean the connector between the gun and the feeding system (6) with a
clean cloth and a detergent.
Every month Dusts or filth Carefully clean the gun with a clean cloth and a detergent, especially the handle, as
ease of holding is a priority.
Every 2 weeks Dusts, filth or material residues After removing the material holder tube (CSG II MP 450 only), carefully clean the
transmission rod or rods with a clean cloth and a detergent, also clean the inside of
the Material holder tube or Cradle of material.
* Time slots are to be intended as actual working time.
* Time slots are to be intended as actual working time.
9- EXTRAORDINARY MAINTENANCE
to be carried out by the maintenance operator / dealer
• Material holder tube gaskets replacement: after extensive use air leakages on the back of the material holder tube may occur.
The outlet OR needs to be replaced. Contact your dealer.
• Replacement of the thrust piston lip gasket : after extensive use an excessive waste of the thrust piston lip seal may occur, thus
leading to a lower performance and air leakage on the front of the gun. The lip seal needs to be
replaced. Contact your dealer.
10- FAULTS AND BREAKDOWNS
to be carried out by the maintenance operator / dealer
In the event of faults and/or breakdowns of gun components, do not try to repair them. Do not use the gun with temporary
repairs or damaged or worn out components, or with non-original components used as a replacement. Repairs shall be carried
out by authorized workshops or directly by the manufacturer. Contact your dealer.
11- FREQUENT ISSUES
12 - WARRANTY
The guns and their tools are covered by the warranty, if not subject to wear and tear, in compliance with European regulations.
All components deemed faulty will be replaced by our technical department with no charges, only if returned without tam-
pering or stains and if delivered DDP to our plant. The manufacturing company is not liable for personal injuries or damage to
property due products or gun misuses, which are expressly forbidden by this manual. In addition the company recommends to
carefully comply with the user’s instructions. The sale of disassembled, altered or incomplete guns or tools (upon specific request
of the client) is not covered by warranty as our technical department could not test and approve them.
INCONVENIENTS CAUSES REMEDIAL ACTIONS
After charging the material and connecting
the gun to the system, nothing occurs when
pushing the lever. No feeding. Check disconnector opening on the system. Check pressure
regulators. Check for potential leakages in the tube.
Irregular or slow extrusion Very thick product. Increase air capacity with the flow regulator. Increase air pressure
with the pressure regulator.
Loss of pressure and extrusion power of
the gun. Slow front ring nut. Damaged
cartridge lip Tighten the ring nut properly. Check cartridge user’s instructions.
Replace the damaged cartridge.
The gun does not work properly. Damaged or dirty components. Carry out cleaning and ordinary maintenance operations. If the
issue is due to damaged components, contact your dealer.