manualshive.com logo in svg

Oracle X8-8, Installation Manual

Share
Download
Oracle X8-8 Installation Manual Download Page 128

Preparation Checklists

Logistics Checklist Considerations

Yes

No N/A Comment

How many days in advance must background checks be completed?
Are there any additional security access issues?
Is computer room access available for installation personnel?
Are laptops, cell phones, and cameras allowed in the data center?
Does the building have a delivery dock?
Is there a delivery/unpacking/staging area?
Is the delivery inside?
If the delivery is not inside, then is the site prepared for uncrating?
Is the unpacking/staging area protected from the elements?
Does the building have adequate receiving space?
Is the unpacking area air-conditioned to avoid thermal shock for various hardware

components?
Will sufficient moving personnel be available to install the hardware?
Are you prepared for uncrating and trash removal?
Are there any restrictions on delivery and trash removal?
Are there any restrictions on delivery truck length, width or height?
Are cardboard boxes and other packing material allowed in the computer room?
Is there a time constraint on dock access? If yes, then provide time constraints.
Is tail lift required on delivery carrier to unload the equipment at the delivery dock?
Will any of the following be required to place equipment in computer room?

Stair walkers

Lifters

Ramps

Steel plates

Floor covers
Does the delivery carrier require any special equipment, such as non-floor damaging

rollers, transport dollies, pallet jacks, or fork lifts?

Related Information

■

“Server Physical Specifications” on page 13

■

“Receiving and Unpacking Requirements” on page 14

■

Oracle Server X8-8 Service Manual

■

Oracle Server X8-8 Safety and Compliance Guide

128

Oracle Server X8-8 Installation Guide • June 2019

Summary of Contents for X8-8







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands