Oracle X4-2B Installation Manual Download Page 65 | Manualshive

Page: 65 / 118

background image

SG-SAS6-R-REM-Z Host Bus Adapter

Use this section to configure a storage drive for OS installation if you have the
SG-SAS6-

R

-REM-Z (also known as Sun Storage 6 Gb SAS REM RAID HBA, Sun Storage 6 Gb

SAS PCIe RAID HBA) installed on your server module.

Note –

When using the SG-SAS6-R-REM-Z HBA, you

must

create a volume before installing an

OS. The system BIOS does not recognize a drive connected to SG-SAS6-R-REM-Z unless it has
a RAID volume on it (can be RAID0). If there is more than a single volume on the drive, install
the OS on a bootable volume.

To create a RAID volume with the disk before installing an operating system, choose one of the
following methods:

■

“Configuring Storage Drives: SG-SAS6-R-REM-Z (Oracle System Assistant)” on page 65

■

“Configure Storage Drives (LSI WebBIOS Configuration Utility)” on page 69

The Sun Storage 6 Gb SAS PCIe RAID HBA name is supported by Oracle System Assistant.

The Sun Storage 6 Gb SAS PCIe RAID HBA set up in Oracle System Assistant has the following
options:

■

Supports RAID 0 with one or more hard drives

■

Supports RAID 1 with two or more hard drives per volume

■

Can set a volume as a boot device

■

Can display if a volume is the boot device

■

Can display the state of a disk (good, bad, hotspare)

See

“Configure Storage Drives SG-SAS6-REM-Z (Oracle System Assistant)” on page 67

for

instructions on preparing the storage drives with Oracle System Assistant.

▼

Configuring Storage Drives: SG-SAS6-R-REM-Z (Oracle System
Assistant)

You can use the Oracle System Assistant RAID Configuration task to prepare a disk for
operating system installation. Oracle System Assistant is the easiest way to prepare the disk for
operating system installation.

To prepare server hard drives for an OS installation, create a bootable volume for the REM. To
configure the SG-SAS6-R-REM-Z, in Oracle System Assistant System, use RAID 0 or 1 only.

Verify that SG-SAS6-R-REM-Z is installed on the server. See

“Identifying REM Host Bus

Adapters” on page 64

.

Launch Oracle System Assistant.

See

“Accessing Oracle System Assistant” on page 59

.

Before You Begin

1

SG-SAS6-R-REM-Z Host Bus Adapter

65

«
...
63
64
65
66
67
...
»

Summary of Contents for X4-2B























































































































Reviews:

No comments

Related manuals for X4-2B

NEC Express5800 Series

Brand: NEC Pages: 4

NEC Express5800 Series

Brand: NEC Pages: 21

NEC Express5800 Series

Brand: NEC Pages: 10

NEC Express5800 Series

Brand: NEC Pages: 22

NEC Express5800 Series

Brand: NEC Pages: 71

NEC Express5800 Series

Brand: NEC Pages: 166

NEC Express5800 Series

Brand: NEC Pages: 16

NECCare Platinum Express5800/A1160

Brand: NEC Pages: 4

NECCare Gold Express5800/320Fd

Brand: NEC Pages: 11

NEC Express5800/R120d-2E

Brand: NEC Pages: 39

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 244

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 191

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 96

UniServer T1100 G3

Brand: H3C Pages: 66

UniServer R6900 G3

Brand: H3C Pages: 214

UniServer R6700 G3

Brand: H3C Pages: 151

UniServer R4900 G5

Brand: H3C Pages: 16

Brand: Crown Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands