manualshive.com logo in svg

Omron NX-IA3117, User Manual

Share
Download
Omron NX-IA3117 User Manual Download Page 90

4   Installation and Wiring

4 - 22

NX-series Digital I/O Unit User’s Manual (W521)

Precautions for Safe Use

• Do not press the flat-blade screwdriver straight into the release hole. Doing so may break the 

terminal block.

• When you insert a flat-blade screwdriver into a release hole, press it down with a force of 30 

N max. Applying excessive force may damage the terminal block.

• Do not tilt or twist the flat-blade screwdriver while it is pressed into the release hole. Doing so 

may break the terminal block.

• Make sure that all wiring is correct.
• Do not bend the cable forcibly. Doing so may sever the cable.

NG

OK

NG

NG

Summary of Contents for NX-IA3117























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands