manualshive.com logo in svg

Omron NX-IA3117, User Manual

Share
Download
Omron NX-IA3117 User Manual Download Page 252

Appendices

A - 22

NX-series Digital I/O Unit User’s Manual (W521)

AC Input Units (Screwless Clamping Terminal Block, 12 mm Width)

Unit name

AC Input Unit

Model

NX-IA3117

Number of points

4 points, independent contacts

External connection 
terminals

Screwless clamping terminal block (8 ter-
minals)

I/O refreshing method

Free-Run refreshing

Indicators

TS indicator, input indicators

Internal I/O common

No polarity 

Rated input voltage

200 to 240 VAC, 50/60 Hz (170 to 264 
VAC, 

3 Hz)

Input current

9 mA typical (at 200 VAC, 50 Hz)
11 mA typical (at 200 VAC, 60 Hz)

ON voltage/ON current

120 VAC min./4 mA min.

OFF voltage/OFF cur-
rent

40 VAC max./2 mA max.

ON/OFF response time

10 ms max./40 ms max.

Input filter time

No filter, 0.25 ms, 0.5 ms, 1 ms (default), 
2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 
128 ms, 256 ms

Dimensions

12 (W) x 100 (H) x 71 (D)

Isolation method

Photocoupler isolation

Insulation resistance

Between each AC input circuit: 20 M

Ω

 

min. (at 500 VDC)
Between the external terminals and the 
functional ground terminal: 20 M

Ω

 min. 

(at 500 VDC)
Between the external terminals and inter-
nal circuits: 20 M

Ω

 min. (at 500 VDC)

Between the internal circuit and the func-
tional ground terminal: 20 M

Ω

 min. (at 

100 VDC)

Dielectric strength

Between each AC input circuit: 3700 
VAC for 1 min at a leakage current of 5 
mA max.
Between the external terminals and func-
tional ground terminal: 2300 VAC for 1 
min at a leakage current of 5 mA max.
Between the external terminals and inter-
nal circuits: 2300 VAC for 1 min at a leak-
age current of 5 mA max.
Between the internal circuit and the func-
tional ground terminal: 510 VAC for 1 min 
at a leakage current of 5 mA max.

I/O power supply 
method

Supplied from external source.

Current capacity of I/O 
power supply terminal

Without I/O power supply terminals

Weight

0.50 W max.

Current consumption 
from I/O power supply

No consumption

NX Unit power con-
sumption

60 g max.

Circuit layout

Installation orienta-
tion and restrictions

Installation orientation: Possible in 6 orientations.
Restrictions: No restrictions

IN0 to IN3

C0 to C3

Internal circuits

Terminal block

I/O power

I/O power supply −

I/O power

I/O power supply −

NX bus 
connector 
(left)

NX bus 
connector 
(right)

Summary of Contents for NX-IA3117























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands