manualshive.com logo in svg

Omron NX-IA3117, User Manual

Share
Download
Omron NX-IA3117 User Manual Download Page 78

4   Installation and Wiring

4 - 10

NX-series Digital I/O Unit User’s Manual (W521)

The following are wiring diagrams (examples) for each power supply.

Precautions for Correct Use

Always use separate power supplies for the Unit power supply and the I/O power supply. If 
you supply power from the same power supply, noise may cause malfunctions.

Additional Information

Refer to the user's manual for the Communications Coupler Unit on design for power supply to 
the Slave Terminal.

 

Unit 

power supply 

(24 VDC)

I/O power 

supply

External 

output 

device

I/O 

power 

supply

External 

output 

device

To external 
devices

End Cover

I/O power supply terminals

Unit power supply 
terminals

Communications Coupler Unit

I/O power supply (Supply from external source)

NX Unit

Additional 

NX Unit Power 

Supply Unit

(Example) DC Input Unit

Two-wire 

sensor

Three-wire 

sensor

Additional I/O 

Power Supply Unit

24 VDC Unit 
power supply

24 VDC I/O 

power supply

DC Input Unit

NX Unit 
power supply

To external 
devices

To external 
devices

0

1

IOV

IOV

2

3

IOV

IOV

IOG

IOG

IOG

IOG

UV 

UG

UV

UG

A1

A8

B1

B8

NC

NC

IOV

IOG

A1

A8

B1

B8

IOV

IOV

IOG

IOG

A1

B1

A8

B8

IOV

IOG

The I/O power supply is
separated.

The I/O power 
supply is not
separated.

Additional NX Unit 
Power Supply Unit

Additional 
I/O Power 
Supply 
Unit

NX Unit 
power supply

Internal power 

supply circuit

Summary of Contents for NX-IA3117























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands