manualshive.com logo in svg

Omron NX-IA3117, User Manual

Share
Download
Omron NX-IA3117 User Manual Download Page 67

3 - 11

3   Part Names and Functions

NX-series Digital I/O Unit User’s Manual (W521)

3-

2  Ind

icat

ors

3

3-

2-1  T

S

 Indicator

The meanings of light statuses are described as follows:

3-2-1

TS Indicator

Color

Status

Description

Green

Lit

The Unit is operating normally.
The Unit is ready for I/O refreshing.

Flashing at 2-s 
intervals.

• Initializing
• Restarting is in progress for the Unit.
• Downloading

Red

Lit

A hardware failure, WDT error, or other fatal error that is common to 
all I/O Units occurred.

Flashing at 1-s 
intervals.

A communications error or other NX bus-related error that is common 
to all I/O Units occurred.

Not lit

• No Unit power supply
• Restarting is in progress for the Slave Terminal.
• Waiting for initialization to start

This indicator shows the current status of the Digital I/O Unit and 
its communications status with the Communications Coupler Unit.

Summary of Contents for NX-IA3117























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands