Omron NX-IA3117 User Manual Download Page 1

Page: 1 / 342

User’s Manual

W521-E1-04

Machine Automation Controller

NX-series Digital I/O Units

Machine Automation Controller

NX-series

Digital I/O

Units

Digital I/O Units

User’s Manual

W521-E1-04

NX-ID



NX-IA



NX-OC



NX-OD



NX-MD



Authorized Distributor:

In the interest of product improvement,

specifications are subject to change without notice.

Cat. No. W521-E1-04

0714

OMRON Corporation

Industrial Automation Company

OMRON ELECTRONICS LLC

One Commerce Drive Schaumburg,

IL 60173-5302 U.S.A.

Tel: (1) 847-843-7900/Fax: (1) 847-843-7787

Regional Headquarters

OMRON EUROPE B.V.

Wegalaan 67-69-2132 JD Hoofddorp

The Netherlands

Tel: (31)2356-81-300/Fax: (31)2356-81-388

Contact: www.ia.omron.com

Tokyo, JAPAN

OMRON ASIA PACIFIC PTE. LTD.

No. 438A Alexandra Road # 05-05/08 (Lobby 2),

Alexandra Technopark,

Singapore 119967

Tel: (65) 6835-3011/Fax: (65) 6835-2711

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower,

200 Yin Cheng Zhong Road,

PuDong New Area, Shanghai, 200120, China

Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200

Summary of Contents for NX-IA3117























































































































































































































































































































































Search results

Summary of Contents for NX-IA3117

Reviews:

Related manuals for NX-IA3117

Brands by name

Popular brands

Omron NX-IA3117, User Manual

Search results

Summary of Contents for NX-IA3117

Reviews:

Related manuals for NX-IA3117

Brands by name

Popular brands