Omron K3HB, Technical Communications User'S Manual

Page: 61 / 147

2-16
List of Settings
Section 2
Lis
t of
Se
ttings
Linear Output Level
Note The values beginning with H' in the Monitor/Setting range column are used when setting or monitor-
ing data via communications.
Communications Setting Level
Note The values beginning with H' in the Monitor/Setting range column are used when setting or monitor-
ing data via communications.
Advanced Function Setting Level
Note (1) If the event connector is provided as a standard feature or an event connector is added, use EV
for the “bank selection” set.
(2) The values beginning with H' in the Monitor/Setting range column are used when setting or moni-
toring data via communications.
Variable
type
Address Parameter
name
Charac-
ter
Monitor/Setting range Character Default
setting
Decimal point Unit
C9 0000 Linear current
type
lset. c
H’00000000: 0-20 mA (0), H’00000001: 4-20 mA (1)
0-20
,
4-20 4-20
--- ---
0001 Linear voltage
type lset. v H’00000000: 0-5 V (0), H’00000001: 1-5 V (1),
H’00000002: 0-10 V (2) 0-5 , 1-5 , 0-10 1-5 --- ---
0002 Linear output
upper limit lset. h H’FFFFB1E1 to H’0001869F:
−
19999 to 99999
(Time limit is OFF. Lower limit of P is 0.)
H’00000000 to H’0001869F: 0 to 99999
(Time unit is min.)
H’00000000 to H’000176D7: 0.00.00 to 9.59.59
(Time unit is hr:min:s.)
H’00000000 to H’0001850F: 00.00.0 to 99.59.9
(Time unit is min:s:ms.)
:9999 to 99999
0. 00. 00
to
99999
0. 00. 00
to
9. 59. 59
0. 00. 00
to
99. 59. 9
99999 According to the
decimal position
setting. The time
unit, however, is
indicated as
*.**.** for
hr:min:s and as
**.**.* for
min:s:ms. ---
0003 Linear output
lower limit lset. l Same as above Same as above R: :9999
P:
0
Same as above ---
Variable
type
Address Parameter
name
Charac-
ter
Monitor/Setting range Character Default
setting
Decimal point Unit
CA 0000 Communications
unit number
u-no
H’00000000 to H’00000063: (0 to 99)
0
to
99 1
--- ---
0001 Baud rate bps H’00000000: 9.6 (0), H’00000001: 19.2 (1),
H’00000002: 38.4 (2) 9. 6 , 19. 2 . 38. 4 9. 6 --- kbps
0002 Communications
data length
len
H’00000000: 7 (0), H’00000001: 8 (1)
7
,
8 7
--- bit
0003 Communications
stop bits
sbit
H’00000000: 1 (0), H’00000001: 2 (1)
1
,
2 2
--- bit
0004 Communications
parity
prty
H’00000000: None (0), H’00000001: Even (1),
H’00000002: Odd (2)
none
,
even
,
odd even
--- ---
0005 Send wait time sdwt H’00000000 to H’00000063: (0 to 99) 0 to 99 20 --- ms
Variable
type
Address Parameter
name
Charac-
ter
Monitor/Setting range Character Default
setting
Decimal point Unit
CB 0000 PASS output
change
pass
H’00000000: LL (0), H’00000001: L (1),
H’00000002: PASS (2), H’00000003: H (3),
H’00000004: HH (4)
ll
,
l
,
pass
,
h
,
hh
pass
--- ---
0001 Hysteresis hys H’00000000 to H’0000270F: 0 to 9999 (Time limit is
OFF. Lower limit of P is 0.)
H’00000000 to H’00001747: 0.00.00 to 0.59.59
(Time unit is hr:min:s.)
H’00000000 to H’0000257F: 00.00.0 to 09.59.9
(Time unit is min:s:ms.) 0 to 9999
0. 00. 00
to
0. 59. 59
00. 00. 0
to
09. 59. 9
1 According to the
decimal position
setting. The time
unit, however, is
indicated as
*.**.** for
hr:min:s and as
**.**.* for
min:s:ms. ---
0002 Output OFF delay
off-d
H’00000000 to H’000007CF: (0 to 1999)
0
to
1999 0
--- R:
100 ms
P: ms
0003 Shot output
shot
H’00000000 to H’000007CF: (0 to 1999)
0
to
1999 0
--- R:
100 ms
P: ms
0004 Output logic
out-n
H’00000000: Close in alarm (0),
H’00000001: Open in alarm (1)
n-o
,
n-c n-o
--- ---
0005 Output refresh
stop
o-stp
H’00000000: OFF (0), H’00000001: OUT (1),
H’00000002: ALL (2)
off
,
out
,
all off
--- ---
0009 Bank selection
bnk-c
H’00000000: OFF (0), H’00000001: KEY (1),
H’00000002: EV (2)
off
,
key
,
ev off
(See
note 1.)
--- ---
000A Startup
compensation
timer s-tmr H’00000000 to H’0000270F: (0.0 to 99.9) 0. 0 to 99. 9 0. 0 1 s
000C Standby
sequence
stdby
H’00000000: OFF (0), H’00000001: ON (1)
off
,
on off
--- ---