background image

5.Measurement  and  Recording 

 

 

5-6 

5.4.3 Auto backup and restarting record setting 

When this function is ON in FUN mode, if power turns off during the record, the recorded 
measurement data before the interruption of power is backed up to SD memory card and 
record is resumed after power is back. And the recording restarts. 

Important 

While this function is ON, insert the recordable SD memory card into the SD memory card 
slot. If the SD memory card is not inserted at the time of power activation, the error which 
shows what the output to an SD memory card went wrong will be displayed, and record 
will stop. 
 

5.5 

Outputting File to SD memory card 

Recorded data can be output to SD memory card files when any of the following cases 
happen. 
 
(a) The SET/REC/STOP is pressed (for less than 3 seconds) during recording. 

Recording in the internal memory continues. 

 
(b) The SET/REC/STOP key is held (for 3 seconds or longer) during recording. 

Recording in the internal memory stops. 
  (Refer to "5.4.2 Stopping Recording") 

 
(c) The internal memory becomes full during recording. 

Recording in the internal memory continues. 
(The recording mode must have been set to "Continue mode".) 
(The factory default is set to "Continue mode". Use the PC software to switch the 
recording mode.) 

 
(d) The SET/REC/STOP key is pressed (for less than 3 seconds in RUN mode) during 

non-recording process, when recorded data remains in the internal memory. 

 
(e) The previously recorded data remains in the internal memory when the power is 

supplied. 
This refers to the case that the unit restarts after it is reset during recording due to a 
power failure or the pressing of the reset switch. 

 

5.6 

Cancelling Alarm 

"ALM" turns on when the measured value is more than Hi threshold range, and between Cut 
and Lo threshold, the alarm output turns ON. 
To cancel the retained alarm, hold the MODE key (for 3 seconds or longer).

Summary of Contents for D6FZ-FGS1000




































































































Reviews: