manualshive.com logo in svg

Omron B5L, User Manual, Page: 27 / 72

Share
Download
Omron B5L User Manual Download Page 27

 

  Chapter 2 Installation & Wiring 

2-2 Wiring 

3D TOF Sensor Module B5L User's Manual (No. E596) 

 To power off 

This section describes the operation flow of this product from the end of operation to 
power-off

.

 

・

 

Power-OFF sequence 

 

 

Execute the distance measurement stop command and turn off the power after the 
distance measurement is stopped. 
Refer to "3-2 Basic Process on Host" for details. 
 

Note: If the power supply voltage is dropped to 0V, do not perform the start-up sequence immediately, 

but wait for 5 seconds or more before turning the power back on. 

 

USB connection 

This product is a USB device connected to the host via a USB cable. 
The USB connector of this product is micro USB as shown below. 
- Micro USB compliant (Vbus rating: 0.5A max.) 
- Vbus power supply must be provided from the host. 

Reception unavailable 

Reception available 

Command reception 

Power supply 

The same timing when the power supply 

voltage falls under the lower limit of 21.6V 

27 

 

Summary of Contents for B5L









































































Reviews:

No comments