Okolab UNO-T Manual Download Page 26

Page: 26 / 73

•

DATA-LOG software. The software allows to log and analyze the data provided by UNO-CONTROLLER via
PC. Refer to DATA-LOG user manual for more info.

•

SDK

(OKOLAB

API)

for

integration

third

party

software

http://www.oko-

lab.com/support#soft_int_tools

MINI-USB cable

Figure 24. MINI-USB cable - Connection.

RS232 Serial port

Use a standard RS232 serial cable to connect UNO-CONTROLLER to a PC as shown in Figure 25. This option

is advisable when the PC is at a distance greater than 10 meters from UNO-CONTROLLER.

You can interface with UNO-CONTROLLER via PC by using:

•

DATA-LOG software. The software allows to log and analyze the data provided by UNO-CONTROLLER
via PC. Refer to DATA-LOG user manual for more info.

•

SDK

(OKOLAB

API)

for

integration

third

party

software

http://www.oko-

lab.com/support#soft_int_tools

RS232 serial cable

Figure 25. RS232 serial cable - Connection.

Summary of Contents for UNO-T










































































Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands

Okolab UNO-T, Manual

Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands