Okolab UNO-T Manual Download Page 15

Page: 15 / 73

Installation

The following paragraph illustrates how to install UNO-STAGE-TOP-INCUBATOR.

The following instructions shall give you the possibility to install the unit quickly. For safe operation
of the unit, it is absolutely necessary to read carefully all the instructions and safety notes.

Connection of the Chamber Base and the Chamber Lid

Follow the instructions below to connect the Base and the Lid of the Okolab H301 incubating chamber to

UNO-CONTROLLER (see Figure 8):

Connect the Y-CABLE-1 connector to

“

Base/Lid

”

connector on the rear panel of UNO-CONTROLLER.

Connect the Base cable of the Chamber Base to its corresponding connector of WP-CABLE. Connect the

RED

labeled connector of WP-CABLE to its corresponding connector of Y-CABLE-1.

Connect the Lid cable of the Chamber Lid to its corresponding connector of WP-CABLE. Connect the

YELLOW

labeled connector of WP-CABLE to its corresponding connector of Y-CABLE-1.

Chamber Lid

Chamber Base

UNO-CONTROLLER

Y-CABLE-1

WP-CABLE

Figure 8. Chamber Base and Chamber Lid - Connection.

Tip

►

Connecting cables are equipped with identification tags to guide you through the installation process.

Note

►

If the Base cable or the Lid cable is equipped with a DIN connector, attach it to its corresponding

connector of Y-CABLE-1.

Connection of GF-MIXER-HM (Humidity Module)

This section describes how to install GF-MIXER-HM, the Humidity Module, included in UNO-T-H-

PREMIXED and UNO-T-H-CO2 configurations. Follow the steps below for a correct installation:

Connect TUBE-E to the connector located inside the Humidifier Cap (see image 1 in Figure 9).

Fill the Humidifier Bottle with distilled water and insert the TUBE-E with the Humidifier Cap. Make sure

to place the O-

RING on the lip of Humidifier Bottle’s n

eck (see image 2 in Figure 9).

Screw the Humidifier Cap and place the Humidifier Bottle in its heater (see image 3 in Figure 9).

The Humidifier Cap is equipped with a Gas Inlet connector, barb connector for 4 mm I.D. silicon tube, and

a Gas Outlet connector, push to fit connector for 6 mm O.D. rigid tube (see image 4 in Figure 9).

Summary of Contents for UNO-T










































































Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands

Okolab UNO-T, Manual

Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands