manualshive.com logo in svg

OETIKER CC 20, Instruction Manual, Page: 49 / 58

Share
Download
OETIKER CC 20 Instruction Manual Download Page 49

 

 

Clamp pincer CP 10 / CP 20 / CC 20 

8 Appendix 

Issue 06.19 

08902961 

8-49 

8 

Appendix 

8.1 

General information in event of faults 

If the closure operation of clamp pincer CP 10 / CP 20 / CC 20 does not start or does not operate correctly, 
consult maintenance personnel responsible for clamp pincer CP 10 / CP 20 / CC 20. 

 

8.2 

Reaction in event of faults 

If a fault occurs, the clamp pincer will be blocked. The service LED will light up red or orange. Operation can be 
restarted only by briefly removing the battery and reinserting it ("reset"). 

If after the clamp pincer have been “reset” the fault is still present, contact your OETIKER contact person. 

 

8.3 

Error messages and troubleshooting measures 

 

INFO 

Closure-relevant error messages can be read out with PC software (individual or multiple report). 

 

Please send the respective reports to your OETIKER contact person. 

 

Service LED 

 

Fig. 38:  Service LED 

Display after the pressing operation 

Cause / remedy 

 

lights up green 

Closure force OK. 

  

 

flashes green/red 

Closure force OK, service interval exceeded. 

 

Have the device serviced. 

 

lights up red 

Closure force 

incorrect

 or hardware error 

 

Recalibrate the device. Repeat the joint. Contact the 
Service Center if necessary. 

 

lights up orange 

Temperature error. 

 

Warm up the tool or cool it down. 

Summary of Contents for CC 20



























































Reviews:

No comments