Oce TCS500 User Manual Download Page 263

Page: 263 / 306

263

Overview

Printhead error messages

The table below gives on overview of the printhead-related error codes.

[89]

Error
code

Description

Customer action

4501 -
4509

Excessive leakage current
detected for head [1…9]
Printhead failing
Replace printed [1…9]

Replace the printhead by using the
wizard.

Note:

Never re-insert a

printhead that has
caused this problem.

4551 -
4559

Head defective during printing

Printhead is probably not placed
correctly. Remove and re-insert the
printhead at the original position.

Note:

If the problem

persists you must replace
the printhead.

4571 -
4579

Head too hot during printing

You can ignore this problem by
pushing the 'OK' button.

Note:

If the problem

re-occurs after a short
time you must replace
the printhead.

4581 -
4589

Head [1….9] keeps heating

Replace the printhead by using the
wizard.

4951 -
4959

WOM memory failure for head
[ 1……9]

Service warning only. No customer
intervention needed.

4961 -
4969

Heating of head [1……9] failed Continue printing until the message

'Replace printhead' displays on the
operator panel.
Then replace the printhead by using
the wizard.

Summary of Contents for TCS500



















































































































































































































































































































Search results

Summary of Contents for TCS500

Reviews:

Related manuals for TCS500

Brands by name

Popular brands

Oce TCS500, User Manual

Search results

Summary of Contents for TCS500

Reviews:

Related manuals for TCS500

Brands by name

Popular brands