Oce TCS500 User Manual Download Page 224 | Manualshive

Page: 224 / 306

background image

224

Chapter 10 License management with Océ License Logic

Introduction to Océ License Logic

Introduction to Océ License Logic

Introduction

The Océ applications and options are protected against unauthorised use. You need
to activate the license to enable an application or option for use. Océ License Logic
enables you to manage the licenses very easy.

This section describes the following.

■

The basic concept of Océ License Logic

■

How to use Océ License Logic.

The possibilities of Océ License Logic

Introduction

Océ License Logic has the following possibilities.

Possibilities

■

View the current active licenses

■

Get the host id of the Océ system

■

Save the active licenses

■

Perform a license activation job.
You can activate new licenses or saved licenses.

«
...
222
223
224
225
226
...
»

Summary of Contents for TCS500



















































































































































































































































































































Reviews:

No comments

Related manuals for TCS500

Brand: DataCard Pages: 8

Brand: Xerox Pages: 34

Brand: Panasonic Pages: 155

Brand: Panasonic Pages: 160

Brand: Samsung Pages: 2

Brand: TallyGenicom Pages: 175

Brand: Oki Pages: 98

Brand: Savin Pages: 160

Brand: Flashforge Pages: 36

Brand: Intermec Pages: 38

Brand: Rokit Pages: 16

Brand: Swift Pages: 14

Brand: Olivetti Pages: 293

Magicolor 2530 DL

Brand: Konica Minolta Pages: 10

Brand: BIG TREE TECH Pages: 11

LaserPro X500 III-80Y

Brand: GCC Technologies Pages: 127

Brand: SPRT Pages: 18

Brand: Renkforce Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands