Oce TCS500 User Manual Download Page 237 | Manualshive

Page: 237 / 306

background image

237

Clean the scan area

Result

The Océ TCS500 scanner is calibrated and the scan quality is correct again.

Clean the scan area

Introduction

You need to keep the glass plate clean. A dirty glass plate causes a decreased copy
and scan quality. Clean the glass plate when you have lines on the image that are not
on the original.

Required tools

Océ cleaner A, part of cleaning kit with codenumber 1068117
Two lint-free cloths

Attention:

Use Océ cleaner A to get the best results.

Attention:

Make sure you do not damage the sensor at the right of the glass

plate.

How to clean the glass plate

1.

Turn off the Océ TCS500 scanner.

2.

Pull the top cover towards you and lift the top cover to open it.

[180]

[180] Open the top cover

«
...
235
236
237
238
239
...
»

Summary of Contents for TCS500



















































































































































































































































































































Reviews:

No comments

Related manuals for TCS500

Brand: IBM Pages: 16

Figure 4 Standalone

Brand: 3D Systems Pages: 2

Jetprinter Disney Edition Z615 Series

Brand: Lexmark Pages: 2

Brand: Oki Pages: 154

Brand: Oki Pages: 121

Brand: Oki Pages: 52

Brand: Oki Pages: 96

Brand: Partex Pages: 16

SCX 4500W - Personal Wireless Laser Multi-Function...

Brand: Samsung Pages: 113

imageRUNNER ADVANCE 8105

Brand: Canon Pages: 5

imageCLASS MF269dw

Brand: Canon Pages: 32

Brand: Samsung Pages: 158

Brand: Savin Pages: 160

Brand: Kodak Pages: 2

Brand: Savin Pages: 160

Brand: Xerox Pages: 205

Brand: WANHAO Pages: 18

Brand: Ricoh Pages: 552

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands