Oce TCS500 User Manual Download Page 262

Page: 262 / 306

262

Chapter 12 System messages and solutions

Overview

The Océ TCS500 printer

Overview

Definition

This table gives an overview of the possible error messages and system messages of
the Océ TCS500 printer and refers to the possible solution.

[88]

Error message / System
message

Description / solution

'Required media not available'

The media required for the job is not available on
the printer.
(

see ‘Required media not available’ on

page 264

)

'Roll empty'

The end of the roll of media is reached while you
print
(

see ‘End of roll’ on page 264

)

'Close maintenance door' /
'Close top cover.'

A door or cover is open, although you are not in
a wizard
(

see ‘Cover or door opened’ on page 265

)

'Remove media'

A media jam occurred
(

see ‘Remove jammed media’ on page 266

)

'Temperature out of range'
/'Humidity out of range'

Excessive temperature or humidity.
(

see ‘Temperature or humidity out of range’ on

page 267

)

'Warning Carriage away from
home position too long'

The carriage is away from its home position too
long
(

see ‘Carriage away from home position too

long’ on page 268

)

The Océ Queue Manager contains damaged jobs
that you cannot delete.
(

see ‘Clear the set memory’ on page 268

)

'System error'

A system error occurred.
(

see ‘Correct system errors’ on page 269

)

'Permanent error'

An permanent error occurred.
(

see ‘Deal with permanent errors’ on page 270

)

Summary of Contents for TCS500



















































































































































































































































































































Search results

Summary of Contents for TCS500

Reviews:

Oce TCS500, User Manual, Page: 262 / 306

Search results

Summary of Contents for TCS500

Reviews: