Oce 9400-I User Manual Download Page 17 | Manualshive

Page: 17 / 159

background image

Getting started

17

■

During the copying process:
If you press this button while an original is being fed in, the process will stop
immediately. If you want to abort a multi-copy job after the scanning of the
original is finished, you must abort the copying process by pressing the
'cancel/continue' button on the printer. You must open the top cover of the
scanner to remove the original (‘Clearing original jam’ on pag e124).

Media button

This button allows you to choose the copy material input.

Possible input selections are Roll 1, Roll 2, or Manual feed.

Exposure scale

You modify the exposure level with the 'lighter' and 'darker'

buttons. The exposure level can be changed at any time.

Auto-exposure button

Automatic Background Compensation can be switched

on or off by using this button.

Cut button

This button toggles between synchro cut mode and standard cut

mode.
In synchro cut mode, the copy is cut to the length of the original.
In standard cut mode, the copy is cut to a standard length.

Edge button

This button toggles between the leading and trailing edge. This

allows you to add or remove a strip at the leading or trailing edge.

Zoom button

You can vary the zoom factor with the range of 25% to 400%. A

fixed increment or a percentage can be used.

Up/Down buttons

When using zoom-, edge-, or the standard-cut modes, you

can modify the values of these modes by pressing the up or down buttons.

Start indicator

This indicator, located above the start button, indicates that the

scanner is ready to perform a scan and turns off while the scanner is scanning
an original. This is also the only indicator that is turned on while the scanner
is in stand-by mode.

Please wait

This indicator flashes when the user has pressed the start button,

but the system is not ready to scan. This could be because the system is busy
with a multi-copy job, or because the system is processing a print job.

Printer error

This indicator activates if there is a printer error. Check the

operating panel of the printer for the error message.

«
...
15
16
17
18
19
...
»

Summary of Contents for 9400-I
































































































































































Reviews:

No comments

Related manuals for 9400-I

Brand: uBuild-3D Pages: 12

Brand: Chamiin I&C Pages: 18

Brand: Xerox Pages: 13

Brand: Muratec Pages: 213

Brand: Copystar Pages: 2

Brand: Xerox Pages: 3

Brand: Kyocera Pages: 2

Brand: Ricoh Pages: 23

Brand: SEWOO Pages: 24

Brand: HCC Technology Pages: 71

GG IMAGE P4100 Series

Brand: G&G Pages: 102

Brand: WOOSIM Pages: 27

Brand: Toshiba Pages: 242

Brand: Brother Pages: 144

Brand: Brother Pages: 276

Brand: EC Line Pages: 16

Brand: Ricoh Pages: 776

WorkCentre 3615

Brand: Xerox Pages: 214

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands