NWA3D Afinibot A31 User Manual Download Page 14 | Manualshive

Page: 14 / 43

background image

NWA3D A31 User Manual

5. Check the tension of the belt driving the X-axis (on the gantry). The belt

should be taut, with no slack or slop. If the belt is loose:
a. Loosen the two bolts at the right side of the gantry holding the belt

follower pulley to the gantry.

b. Using an Allen wrench as a lever, push the follower pulley to tighten the

belt.

c. Holding the belt taut, tighten the two bolts.

© 2018 NWA3D LLC

13

«
...
12
13
14
15
16
...
»

Summary of Contents for Afinibot A31












































Reviews:

No comments

Related manuals for Afinibot A31

ExpressCard 2000

Brand: Magtek Pages: 25

Brand: idp Pages: 48

Brand: VASTEX Pages: 8

Brand: Brady Pages: 48

Brand: Cisco Pages: 43

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 103

Brand: Argox Pages: 156

Brand: SprintRay Pages: 6

Brand: Samsung Pages: 2

Brand: Samsung Pages: 13

Brand: Samsung Pages: 37

Brand: Samsung Pages: 2

CLX-4195 Series

Brand: Samsung Pages: 20

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands