NWA3D Afinibot A31 User Manual Download Page 13 | Manualshive

Page: 13 / 43

background image

NWA3D A31 User Manual

c. Re-check the tension of the nozzle assembly. The assembly and the belt

should move left and right without much effort, but there should have no
side-to-side wiggle or play.

4. Check the tension of the belt driving the Y-axis (under the build plate). The

belt should be taut, with no slack or slop. If the belt is loose:
a. Loosen the four bolts at the front of the base frame holding the belt

follower pulley to the base frame.

b. Using an Allen wrench as a lever, push the follower pulley away from the

frame to tighten the belt.

c. Holding the belt taut, tighten the four bolts.

© 2018 NWA3D LLC

12

«
...
11
12
13
14
15
...
»

Summary of Contents for Afinibot A31












































Reviews:

No comments

Related manuals for Afinibot A31

Brand: OKIDATA Pages: 13

Brand: Seiko Pages: 76

Invent3d Series

Brand: Inventorcloud Pages: 4

Brand: Zonestar Pages: 25

Brand: Oki Pages: 140

Brand: Oki Pages: 2

DocuPrint C3300 DX

Brand: Xerox Pages: 200

Brand: Mitsubishi Pages: 2

Brand: Xerox Pages: 109

Brand: Paradise POS Pages: 275

Brand: Rice Lake Pages: 86

Brand: Canon Pages: 707

Brand: Canon Pages: 339

Brand: Ioline Pages: 78

Brand: Fastjet Pages: 48

Brand: Fargo Pages: 68

Brand: Roland Pages: 78

Brand: Canon Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands